New Jersey Administrative Code

Approved rear view mirrors shall be mounted inside and outside of a Type S school vehicle. Outside mirrors shall be mounted on both sides of the Type S school vehicle. Notes N.J. Admin. Code § 13:20-51.11 Amended by R.2012 d.023, effective 2/6/2012. See: 43 N.J.R. 1831(a), 44 N.J…

The rear window shall be non-ventilating. Notes N.J. Admin. Code § 13:20-51.12

(a) Securely fastened seats and backrests shall be provided. Seats shall be forward facing and shall be spring or foam rubber upholstered. (b) A "jump-type" or folding seat shall not be permitted. (c) Each seat exit shall be clear of obstructions. (d) A vehicle shall not be used …

An adjustable sun visor shall be provided. Notes N.J. Admin. Code § 13:20-51.14

A windshield wiper(s) shall be provided so as to provide clear vision for the driver. Notes N.J. Admin. Code § 13:20-51.15

(a) Pursuant to N.J.A.C. N.J.A.C. 6A:27-7.13, each school bus shall be equipped with a properly designed and installed sensor to determine the presence of person(s) or object(s) located in, but not limited to, the front and back of the school bus. (b) All equipment subject to ins…

The following words and terms, when used in this subchapter, shall have the following meanings unless the context clearly indicates otherwise. "Accident" means: 1. A collision involving a school bus or vehicle that results in personal injury or death, or causes disabling damage t…

(a) No more than nine passengers excluding the driver, may be transported in each Type S school vehicle. Fifteen inches of seat length shall be provided for each passenger. (b) There shall be no standees. Notes N.J. Admin. Code § 13:20-51.3 Amended by R.2012 d.023, effective 2/6/…

The drive wheels of Type S school vehicles shall be equipped with tire chains, all-weather tires, or snow tires for safe operation in areas of snow and/or ice. Notes N.J. Admin. Code § 13:20-51.4 Amended by R.2012 d.023, effective 2/6/2012. See: 43 N.J.R. 1831(a), 44 N.J.R. 287(b…

(a) Emergency equipment shall be provided consisting of at least the following: 1. A seat belt cutter; 2. A spare tire; 3. A jack; 4. A lug wrench; and 5. Three red reflectorized triangular warning devices. Notes N.J. Admin. Code § 13:20-51.5

(a) A fully-charged dry chemical fire extinguisher with a pressure gauge approved by the UL with the minimum UL rating of B2, C2, 1/2BC, or 10BC shall be provided. The fire extinguisher shall be mounted in a bracket in a convenient location in the driver's compartment. (b) A Type…

(a) A removable first aid kit may be provided. The first aid kit shall be a moistureproof and dustproof container without a lock. When the first aid kit is stored in a storage compartment, the location of the kit shall be identified by the words "First Aid" in red letters two inc…

A securely attached nonskid material floor covering shall be provided. Notes N.J. Admin. Code § 13:20-51.8

The heater shall be capable of bringing the interior temperature of the Type S school vehicle up to and maintaining a minimum temperature of 50 degrees Fahrenheit. Notes N.J. Admin. Code § 13:20-51.9 Amended by R.2012 d.023, effective 2/6/2012. See: 43 N.J.R. 1831(a), 44 N.J.R. 2…

(a) Each contractor and district board of education shall furnish liability insurance for bodily injury and property damage in the amount of $ 1,000,000 combined single limit per occurrence for all vehicles which are used for pupil transportation to and from school and school rel…

(a) To ensure the safety of students, this subchapter shall apply to school buses originally designed by the manufacturer to carry 10 or more passengers used in the transportation of children to or from school pursuant to N.J.S.A. 39:1-1 and that operate in whole or in part on al…

An automatic fuel supply shut-off valve shall be installed in a protected location adjacent to the manual shut-off valve on all school buses and shall be activated by engine vacuum or oil pressure. Notes N.J. Admin. Code § 13:20-53.10

Means shall be provided in the fuel system to prevent the flow of gaseous fuel to the carburetor when the ignition is in the "off" or "accessory" position, or from the carburetor when engine vacuum or oil pressure is not present. Notes N.J. Admin. Code § 13:20-53.11

A dual fuel system using liquid and gaseous fuels shall have an automatic shut-off valve installed in the liquid fuel line to the carburetor. Notes N.J. Admin. Code § 13:20-53.12

A by-pass relief device shall be installed in the fuel pump or between the fuel pump and the automatic shut-off valve in the liquid fuel line to the carburetor on a school bus equipped with a dual fuel system for the use of gasoline and gaseous fuels. The relief device need not b…

(a) Radio transmitters, radio receivers, electric motors, or other electrical equipment (except lamps and wiring) shall not be mounted in a compartment with fuel supply containers, unless one of the following conditions is met: 1. All piping, connectors, and valves on the fuel su…

The fuel system, including the fuel supply container, shall be installed with as much road clearance as possible. The lowest part of any component in the fuel system, including protective guards and fuel cradles, shall not be lower than the lowest edge of the vehicle differential…

The gasoline tank shall not be placed below the aisle to a door unless the area over such tank is adequately protected by metal shielding. Notes N.J. Admin. Code § 13:20-53.16

Diesel or gasoline fuel tanks shall be certified and marked by the manufacturer to be in compliance with United States Department of Transportation requirements. Notes N.J. Admin. Code § 13:20-53.17

All parts of the fuel system shall be securely installed outside of the passenger compartment and shall be located so as to prevent damage to any part of the passenger compartment. Notes N.J. Admin. Code § 13:20-53.18

(a) Fuel containers for all fuels shall conform to 49 CFR § 393.65, incorporated herein by reference, as amended and supplemented. (b) A fuel container for liquid fuel shall, in addition to (a) above, conform to 49 CFR § 393.67, incorporated herein by reference, as amended and su…

The following words and terms, when used in this subchapter and in N.J.A.C. 13:20-53A, 53B, and 53C, shall have the following meanings unless the context clearly indicates otherwise. "Alteration" means any change in the construction, design, or installation of a fuel supply conta…

(a) The installation of LPG, CNG, or LNG fuel systems on school buses equipped with gaseous fuel carburetors shall be in accordance with the following requirements: 1. Fuel supply containers on school buses shall not be located in or above the passenger compartment; and 2. Fuel s…

(a) Fuel supply containers shall meet all applicable requirements of the ASME Code, 49 CFR § 393.67, incorporated herein by reference, as amended and supplemented, and the following requirements: 1. Each container and cradle shall be mounted in a protected location to minimize da…

Markings of set-to-discharge pressure for safety relief devices and working pressure of fuel supply containers required by this subchapter shall be visible either directly or by use of a mirror after installation. All remote filling inlets shall be visibly marked with the type of…

(a) All safety devices that may discharge to the atmosphere shall be vented to the outside of the school bus, and all discharge lines and outlets shall be installed as follows: 1. Discharge lines shall be constructed of metal other than aluminum and shall be of a size and so loca…

Manifolds connected to fuel supply containers shall be supported to minimize vibration and shall be installed in a protected location or shielded to prevent damage from unsecured objects. A normally closed automatic shut-off valve that is held open by electrical current shall be …

(a) All pipes, tubing, hoses, and fittings shall meet the following requirements: 1. All materials and assemblies shall be designed for the widest pressure and temperature ranges to which they may be subjected with a pressure safety factor of at least four. 2. All materials, incl…

(a) Every gasoline or diesel fuel supply line shall have the fuel supply line fitting located in the top of the tank. (b) Supply lines passing through a panel shall be protected by grommets or similar devices, which shall snugly fit both the supply lines and the holes in the pane…

In addition to the NFPA Standard 58A "Liquefied Petroleum Gases Engine Fuel Systems," incorporated herein by reference, as amended and supplemented, in effect at the time of installation, fuel systems using LPG shall also meet the requirements of this subchapter. Notes N.J. Admin…

A vapor equalizing valve may be installed in the fuel supply container. The valve shall be capped, except when filling, to withstand the maximum pressure of the container. Notes N.J. Admin. Code § 13:20-53A.10

A manually-operated shut-off valve shall be installed in the fuel supply container outlet connection serving the supply line and shall be marked "SHUT-OFF VALVE." Notes N.J. Admin. Code § 13:20-53A.11

(a) Every LPG fuel supply container shall be equipped with a liquid volume gauge, which shall be designed and installed as follows: 1. The gauging device shall be a type that has been listed by the UL or by any other nationally recognized testing laboratory as meeting the UL requ…

An automatic pressure reducing regulator or a vaporizer regulator designed to withstand a service pressure of at least 250 pounds per square inch shall be installed between the LPG fuel supply container and the carburetor. All regulators and vaporizers shall be of a type that has…

Every compartment in which an LPG fuel supply container is installed shall be vented to the atmosphere unless all piping and connectors are outside of the compartment. The vent or vents shall be installed as per manufacturer's specifications. Notes N.J. Admin. Code § 13:20-53A.14…

(a) All LPG hose and hose assemblies shall have a working pressure of not less than 350 pounds per square inch and a burst pressure of not less than 1,750 pounds per square inch. (b) Each LPG hose shall be reinforced with corrosion-resistant wire braid and shall be of a type that…

(a) Each LPG fuel supply container shall be constructed, inspected, and permanently marked in accordance with 49 CFR § 393.69, incorporated herein by reference, as amended and supplemented, or the ASME Code provision. (b) Fuel supply containers constructed to the United States De…

When two or more fuel supply containers are used, a back-flow check valve with a pressure setting not higher than 500 pounds per square inch shall be installed between the back-flow check valves and the filling operation. A hydrostatic relief valve with a pressure setting not low…

(a) Each LPG fuel supply container constructed in accordance with ASME specifications shall be permanently marked with the following information: 1. The official ASME Code U symbol; 2. The manufacturer's name, initials, or trademark; 3. The maximum allowable working pressure in p…

Each valve shall be of a type that has been tested and listed by the UL or by any other nationally recognized testing laboratory as meeting the UL requirements for LPG. Each valve shall be securely mounted and shielded or installed in a protected location to prevent damage from e…

(a) One or more spring-loaded internal safety relief valves shall be installed in each fuel supply container that is connected to vapor space. (b) The fuel supply container shall be permanently marked to indicate the "set to discharge pressure" after the safety relief valves have…

(a) Permanent markings on safety relief valves in ASME fuel supply containers shall include: 1. The manufacturer's name, initials, or trademark; 2. The manufacturer's design or type number; 3. The discharge pressure in pounds per square inch; 4. The discharge capacity in cubic fe…