Aerospace Upstart Petitions FAA for Operational Ease

2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems

In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.

2026-13440, Enabling Supersonic Overland Flight

The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.

2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period

The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.

2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility

The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.

2026-17553, Airworthiness Directives; The Boeing Company Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by a Boeing investigation for manufacturing errors and excessive preload forces at the lower side of body (SOB) splice plates common to the lower outboard wing skins. That investigation concluded that shim gaps may have exceeded engineering allowances, and high pull up forces on the components may cause fatigue cracks to form at the fastener holes. This AD requires, depending on configuration, repetitive ultrasonic (UT) inspections at certain splice plates, rear spar terminal fittings, lower chords, front spar terminal fittings, and jack pads for any cracks; repetitive detailed inspections (DET) of certain splice plates for any cracks; and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.

2026-17552, Airworthiness Directives; Airbus SAS Airplanes

The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A320-211, -212, -214, -216, -231, -232, and - 233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by a fatigue test that identified cracks in the forward and aft upper corner of the bulk cargo door. This AD requires a rototest inspection for cracks and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.

Previous: 2025-09282, Petition for Waiver of Compliance; Extension of Comment Period

The Association of American Railroads asked for a break from some track inspection rules, and now everyone gets more time to share their thoughts. This extension means folks can weigh in longer before any decisions are made, helping keep trains safe and rules fair. No money changes yet, just extra time to speak up!

Next: 2025-09287, Petition for Exemption; Summary of Petition Received; Helicopter Wildlife Services

Helicopter Wildlife Services asked the FAA to ease some flying rules so they can do their work better and safer. This change mainly affects their pilots and operations, aiming to save time and possibly cut costs. The FAA wants everyone to know about this and share their thoughts before making a final decision.