Airbus Helicopter Operators Face New Tail Rotor Inspections
Published Date: 7/2/2025
Rule
Summary
If you fly or fix certain Airbus Helicopters Deutschland models, listen up! Starting July 18, 2025, you’ll need to inspect key parts of the tail rotor controls to prevent dangerous failures. These checks might cost some time and money but keep everyone safe and sound in the skies.
Analyzed Economic Effects
5 provisions identified: 0 benefits, 5 costs, 0 mixed.
Mandatory tail-rotor inspections starting July 18, 2025
If you operate or maintain the listed Airbus Helicopters Deutschland models (EC135P1, EC135P2, EC135P2+, EC135P3, EC135T1, EC135T2, EC135T2+, EC135T3, and EC635T2+ with serials 0001–1999), you must perform visual inspections of ball pivots P/N 92-201-00 and 92-207-00, fluorescent penetrant inspection of control rods P/N L672M2006101 and L672M2006102, and inspection/measurement of yaw actuator assemblies P/N L672M2005104, L672M2005105, and L672M2005106. These actions are required in accordance with EASA AD 2025-0108 and must be done within the compliance time stated in this AD (the FAA noted a compliance time of within 50 hours time-in-service or 90 days, whichever occurs first). Depending on inspection results, you must do corrective actions including part replacement as required.
Potential part-replacement costs if damage found
If inspections find damage, the AD lists on-condition replacement costs per helicopter: adapter $888, ball pivot $2,931, close-tolerance bolt $127, connector cover $656, control rod $6,920, input lever $9,925, and rod end $728 (each cost per product includes parts and labor as shown). The FAA did not estimate how many helicopters will need replacements.
FAA estimate: 318 helicopters affected and per-action labor costs
The FAA estimates this AD affects 318 U.S.-registered helicopters. For each helicopter the FAA lists labor cost estimates of $170 for each of the three required inspection actions (inspect ball pivot and control rod; fluorescent penetrant inspection; inspect and measure yaw actuator interfaces) and $85 to report results.
Installation and flight-permit restrictions
The AD prohibits installing affected parts unless the part is serviceable and meets the AD's requirements. The rule also explicitly prohibits special flight permits for affected helicopters. These restrictions take effect as of July 18, 2025.
Mandatory reporting and paperwork burden
You must report inspection results to Airbus Helicopters Deutschland: for inspections done on or after July 18, 2025, submit the report within 15 days after the inspection; for inspections done before July 18, 2025, submit within 15 days after July 18, 2025. The FAA states public reporting is estimated to take about 1 hour per response and cites OMB Control Number 2120-0056.
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2025-04846, Extension of the Prohibition Against Certain Flights in the Territory and Airspace of Libya
The FAA is extending the ban on certain flights over Libya for three more years, until March 20, 2028. This affects U.S. airlines, commercial operators, and pilots with FAA certificates flying in Libyan airspace, due to ongoing safety risks. The rule also reminds everyone how to apply for special approvals or exemptions if needed.
2025-03853, Enforcement Policy Regarding “Drug and Alcohol Testing of Certificated Repair Station Employees Located Outside of the United States; Correction”
The FAA is giving repair stations outside the U.S. a break by delaying enforcement of new drug and alcohol testing rules until March 20, 2025. This means affected repair stations don’t have to worry about penalties if they aren’t fully following the updated rules just yet. The delay helps everyone get ready without rushing or extra costs.
Previous / Next Documents
Previous: 2025-12377, Airworthiness Directives; Airbus Helicopters
If you own or operate an Airbus H160-B helicopter, listen up! The FAA found that a key part in the main rotor, called the swashplate bearing, can wear out too soon. Starting July 17, 2025, you’ll need to regularly check and grease this part, run special flight tests, and fix any issues fast to keep flying safe and sound.
Next: 2025-12396, Revising the Duration of Design Certifications
The Nuclear Regulatory Commission is changing how long nuclear plant design certifications last—from 15 years to 40 years! This update affects current and future certifications, making things simpler and longer-lasting without changing their start dates. The new rule kicks in on September 15, 2025, giving companies more time and stability without extra costs.