FAA's High-Tech Safety Solution: Red Paint on Helicopter Parts
Published Date: 11/25/2025
Rule
Summary
If you fly an Airbus EC120B helicopter, listen up! The FAA is updating safety rules to keep your tail rotor in top shape by adding a cool red paint mark to help spot loose parts. Starting December 30, 2025, you’ll still do regular inspections, but this new paint job means fewer checks over time—saving you time and possibly money while keeping flights safe.
Analyzed Economic Effects
5 provisions identified: 0 benefits, 4 costs, 1 mixed.
Immediate repetitive inspections required
If you operate an Airbus Helicopters Model EC120B, you must visually inspect the tail rotor (TR) hub body for cracks within 15 hours time-in-service (TIS) or 7 days after December 30, 2025, and then at intervals not to exceed 15 hours TIS. You must also visually inspect the TR splined flange at the same 15-hour/7-day intervals and replace parts before further flight if cracks or other disqualifying conditions are found.
Hardware replacement schedule and thresholds
For EC120B helicopters with 9,000 or more total hours TIS or unknown hours, you must, within 15 hours TIS or 7 days after December 30, 2025, remove and replace each bolt, washer, and nut on the TR hub body and then repeat that removal/replacement at intervals not to exceed 1,000 hours TIS. For helicopters with less than 9,000 total hours TIS, you must do this within 1,000 hours TIS or before reaching 9,000 hours TIS and then every 1,000 hours TIS thereafter.
Replacement part cost exposures spelled out
The FAA estimates this AD affects 70 U.S.-registered EC120B helicopters and provides cost estimates: a visual TR hub or spline flange inspection is about $22 per helicopter; replacing a bolt/washer/nut set is about $68; inspecting torque and adding the red paint line is about $340 per helicopter; replacing a TR hub body is estimated at $16,655 per helicopter; replacing a TR spline flange is estimated at $2,993 per helicopter. Labor is estimated at $85 per hour in these calculations.
Torque check and red paint modification ends inspections
Within 24 months after December 30, 2025, operators must inspect the torque on the TR hub nut; if torque is within limits, you must apply a red paint line (polyurethane) to specified bolts, nuts, and washers. Applying the red paint line is a terminating action for the repetitive inspections. If torque is not within limits, the nut must be removed and replaced before further flight. After paint application, you must inspect the red paint line for alignment within 100 hours TIS or 12 months, whichever occurs first, and then at those same intervals.
Parts installation restriction takes effect
As of December 30, 2025, you may not install TR hub body P/N C642A0100103 or a splined flange on any EC120B helicopter unless the part is new (zero hours TIS) or has passed the inspections required by the AD. This limits installation of those part-numbered components until they meet the AD's inspection/new-part condition.
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2026-19843, Notice of Policy Change and Rescission of Single-Pilot Training Exemptions for Certain Cessna Aircraft
Starting September 29, 2026, the FAA is stopping all exemptions that let certain Cessna planes, which normally need two pilots, be flown by just one. Pilots who got special single-pilot training under these exemptions must now follow the two-pilot rule or stop flying those planes solo. This change is all about safety and making sure everyone follows the rules—no more shortcuts!
2026-19729, Airworthiness Directives; Airbus Helicopters
The FAA wants to fix a safety issue on certain Airbus Helicopters because gaps in the engine seals could let fires spread and stop fire extinguishers from working well. They’re proposing to add angle-brackets to the engine firewalls to keep everyone safer. Helicopter owners need to comment by November 12, 2026, and get ready for these changes, which might cost some time and money but will boost safety big time.
Previous / Next Documents
Previous: 2025-20935, Safety Zones; Recurring Events in Captain of the Port Duluth Zone
The Coast Guard is updating safety rules for yearly events in the Duluth area of Lake Superior to keep boaters safer and better informed. They’re adding clear definitions and improving how and when safety zones are enforced, so everyone knows what’s happening and when. These changes start December 26, 2025, and help prevent accidents during busy marine events without adding extra costs.
Next: 2025-20951, Airworthiness Directives; The Boeing Company Airplanes
The FAA is making sure certain Boeing 737 planes get a quick check to fix brake problems that could cause accidents. Starting December 10, 2025, airlines must inspect and test the landing gear brake hoses and sensors to keep flights safe. This fix helps avoid costly crashes and keeps passengers secure, with comments open until January 9, 2026.