Airbus A350 Brake Inspection Rule Targets Missing Landing-Gear Part
Published Date: 11/10/2026
Rule
Summary
If you fly or work with Airbus A350-941 planes, listen up! The FAA found a missing part in the main landing gear brakes that could cause trouble. Starting December 15, 2026, these planes must get special inspections and fixes to keep everyone safe—so airlines should plan for some extra checks and possible repairs soon.
Analyzed Economic Effects
5 provisions identified: 1 benefits, 4 costs, 0 mixed.
Mandatory A350-941 landing-gear inspections
If you operate Airbus SAS Model A350-941 airplanes, the FAA requires inspections and any corrective actions of the main landing gear (MLG) brake rod center pin, nut, lock ring, and end plate beginning December 15, 2026, as specified in EASA AD 2025-0150 (dated July 14, 2025). The inspections are intended to address missing or corroded MLG brake rod center pin nut sub-assemblies that could prevent MLG extension and cause injury or damage.
Operator compliance costs and repair estimates
The FAA estimates this AD affects 3 U.S.-registered A350-941 airplanes. Required inspection actions are estimated at up to 7 work-hours × $85/hr = up to $595 per airplane (up to $1,785 total on U.S. operators). If on-condition repairs are needed, the FAA estimates up to 20 work-hours × $85/hr = $1,700 plus parts costing $30,399, for a total up to $32,099 per airplane for those repairs.
Mandatory inspection reporting and paperwork
The AD requires reporting the results of the inspections (including no findings) to the manufacturer. The Paperwork Reduction Act information lists OMB Control Number 2120-0056 and estimates public reporting takes about 1 hour per response.
Extra work if lockwire/sealant missing on reinstalled pin
For airplanes where any MLG brake rod pin sub-assembly was reinstalled without reinstalling lockwire and applying sealant, the AD introduces additional required work: operators must contact Airbus for instructions and then accomplish those instructions.
Paint-repair deviations need AMOC approval
The FAA denied a request to allow use of alternative paint/primer repair procedures specified in Airbus AOT A32P034-24; instead, any deviation from the vendor paint repair methods identified as Required for Compliance (RC) in the referenced service information requires an approved Alternative Method of Compliance (AMOC).
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2025-04846, Extension of the Prohibition Against Certain Flights in the Territory and Airspace of Libya
The FAA is extending the ban on certain flights over Libya for three more years, until March 20, 2028. This affects U.S. airlines, commercial operators, and pilots with FAA certificates flying in Libyan airspace, due to ongoing safety risks. The rule also reminds everyone how to apply for special approvals or exemptions if needed.
2025-03853, Enforcement Policy Regarding “Drug and Alcohol Testing of Certificated Repair Station Employees Located Outside of the United States; Correction”
The FAA is giving repair stations outside the U.S. a break by delaying enforcement of new drug and alcohol testing rules until March 20, 2025. This means affected repair stations don’t have to worry about penalties if they aren’t fully following the updated rules just yet. The delay helps everyone get ready without rushing or extra costs.
Previous / Next Documents
Previous: 2026-22891, Rules and Regulations, Series 8
The National Labor Relations Board fixed some technical errors in its rules about handling petitions. If you're involved in a case, you have 14 days to respond and can ask to join the case by filing a motion. These updates clarify how the Board decides on its authority, with no extra costs or delays expected.
Next: 2026-22907, Airworthiness Directives; Airbus SAS Airplanes; Correction
The FAA fixed a small mistake in a safety rule for certain Airbus A330 and A340 airplanes. This correction updates a paragraph reference but doesn’t change any safety steps or deadlines. If you operate these planes, nothing new to pay or do—just a clearer rule starting November 23, 2026.