FAA Tweaks TBM Landing Gear Checks, Retiring the Dye Test
Published Date: 11/17/2026
Proposed Rule
Summary
If you own or fly a Daher TBM 700 airplane, the FAA wants you to keep checking the main landing gear for cracks but with some new rules. They’re adding more approved parts and saying no more dye penetrant inspections. You’ve got until January 4, 2027, to share your thoughts, and these changes help keep flights safe without extra costs for replacing gear.
Analyzed Economic Effects
5 provisions identified: 1 benefits, 3 costs, 1 mixed.
Replace MLG to stop inspections (terminating action)
You may stop the repetitive inspections by installing a “serviceable part” (any MLG forging body that is not an affected part) on both left and right MLGs in accordance with the listed service bulletins; replacement is a terminating action for the inspection requirement. The FAA estimates replacement cost at 4 work-hours × $85/hr = $340 plus $6,000 parts, totaling $6,340 per replacement.
Mandatory MLG inspections every 240 landings
If you operate a Daher TBM 700 with an “affected part” (MLG forging body P/N 21236-000-00, 21236-000-01, 22609-000-00, 22609-001-00, 22611-000-00, 22611-001-00, D67685, or D67686) and your airplane serial number is 1–638 or 687, you must do a special detailed inspection of the main landing gear forging body within the stated compliance times and then at intervals not to exceed 240 landings. The FAA estimates 431 U.S.-registered airplanes are affected and estimates the inspection cost at 4 work-hours × $85/hr = $340 per inspection (totaling $146,540 across U.S. operators per inspection).
On-condition and confirmation inspection costs
If a crack is suspected during the SDI, you must remove the MLG leg and confirm the crack with a fluorescent penetrant inspection (estimated 8 work-hours × $85/hr = $680). If replacement is chosen as the corrective action, the AD estimates parts + labor cost at $6,340 per replacement.
Dye penetrant inspection removed
The rule explicitly removes dye penetrant as an authorized method for the repetitive special detailed inspection; the SDI must be done by eddy current or fluorescent penetrant per the service bulletin and MCAI.
Credit for prior inspections under listed bulletins
If you already performed the required actions before this AD's effective date using the listed Daher service bulletins (Revisions 2, 3, 4, or Revision 4/Revision 3 etc. as specified), you receive credit toward the AD requirements, so you do not need to repeat those actions to comply.
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2025-04846, Extension of the Prohibition Against Certain Flights in the Territory and Airspace of Libya
The FAA is extending the ban on certain flights over Libya for three more years, until March 20, 2028. This affects U.S. airlines, commercial operators, and pilots with FAA certificates flying in Libyan airspace, due to ongoing safety risks. The rule also reminds everyone how to apply for special approvals or exemptions if needed.
2025-03853, Enforcement Policy Regarding “Drug and Alcohol Testing of Certificated Repair Station Employees Located Outside of the United States; Correction”
The FAA is giving repair stations outside the U.S. a break by delaying enforcement of new drug and alcohol testing rules until March 20, 2025. This means affected repair stations don’t have to worry about penalties if they aren’t fully following the updated rules just yet. The delay helps everyone get ready without rushing or extra costs.
Previous / Next Documents
Previous: 2026-23370, Modernizing the Labor Market Test and Improving Protections for U.S. Workers in the PERM Immigrant Visa Program
The Department of Labor wants to update the rules for employers hiring permanent immigrant workers to better protect U.S. workers’ jobs and wages. Changes include tougher job advertising, better notice for layoffs, and using modern tech to review applications faster. Employers and U.S. workers will feel the impact, with public comments open until January 19, 2027, and no immediate cost changes announced.
Next: 2026-23390, Respirable Crystalline Silica and Respiratory Protection
This update fixes a small mistake in the rules about protecting miners from harmful silica dust. It affects underground and surface coal mine operators by clarifying exposure limits to dangerous dust and gases. The correction takes effect November 17, 2026, helping keep miners safer without adding big costs.