FAA Expands Titanium Screw Fix Across Several Falcon Jets
Published Date: 11/19/2026
Proposed Rule
Summary
The FAA wants to update safety rules for certain Dassault Falcon 7X, 900EX, and 2000EX airplanes by replacing more titanium screws in more places and on more planes. This keeps the planes safe by fixing a known problem and limits installing risky parts. Owners need to act by early 2027, so get ready to swap those screws and keep flying safely!
Analyzed Economic Effects
5 provisions identified: 0 benefits, 4 costs, 1 mixed.
Mandatory screw replacement and inspection
If you operate a Dassault FALCON 7X, 900EX, or 2000EX airplane covered by this rule, you must replace certain Decomatic titanium screws, inspect the screw bore dimensions, and perform corrective actions (oversizing or repair) as specified in EASA AD 2025-0228R1 and Dassault Service Bulletin 7X-467. The proposed AD would retain the replacement requirements from AD 2024-14-09 and require the inspection and repair actions described in EASA AD 2025-0228R1 (EASA AD dated February 6, 2026).
Estimated compliance cost and fleet affected
The FAA estimates this proposed AD would affect 52 U.S.-registered airplanes. The FAA estimates up to 250 work-hours at $85 per hour for certain replacements (labor), rental of special tooling at $524 per day for some Model FALCON 7X serial numbers, parts cost up to $21,774, and total estimated cost on U.S. operators up to $1,132,248. The FAA also notes the manufacturer may cover some or all costs under warranty.
More airplanes and locations added
The proposed AD expands which airplanes and which areas on those airplanes are subject to the screw replacement rules: additional Model FALCON 7X airplanes and additional locations on certain FALCON 7X airplanes were added to the applicability. The FAA states this proposed AD would expand applicability beyond AD 2024-14-09.
Limits on installing affected titanium screws
The proposed AD would limit installation of certain affected Decomatic titanium screws under specified conditions, as stated in EASA AD 2025-0228R1. The MCAI and the proposed AD explicitly say the rule 'limits installation of certain Decomatic titanium screws.'
Compliance times set to flight cycles only
EASA AD 2025-0228R1 removed calendar-based compliance times and defines the parts-replacement compliance times in flight cycles (FC) only. This proposed FAA AD would require compliance with the timing specified in EASA AD 2025-0228R1.
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2025-04846, Extension of the Prohibition Against Certain Flights in the Territory and Airspace of Libya
The FAA is extending the ban on certain flights over Libya for three more years, until March 20, 2028. This affects U.S. airlines, commercial operators, and pilots with FAA certificates flying in Libyan airspace, due to ongoing safety risks. The rule also reminds everyone how to apply for special approvals or exemptions if needed.
2025-03853, Enforcement Policy Regarding “Drug and Alcohol Testing of Certificated Repair Station Employees Located Outside of the United States; Correction”
The FAA is giving repair stations outside the U.S. a break by delaying enforcement of new drug and alcohol testing rules until March 20, 2025. This means affected repair stations don’t have to worry about penalties if they aren’t fully following the updated rules just yet. The delay helps everyone get ready without rushing or extra costs.
Previous / Next Documents
Previous: 2026-23576, Airworthiness Directives; Airbus Helicopters Deutschland GmbH (AHD) Helicopters
If you own or operate certain Airbus Helicopters Deutschland models, the FAA wants you to do a one-time check of the tail rotor control system after a hard landing. Depending on what you find, you might need to fix things and update your maintenance manuals. This keeps flying safe and sound, with comments on the plan due by January 4, 2027.
Next: 2026-23581, Airworthiness Directives; ATR-GIE Avions de Transport Régional Airplanes
The FAA wants to update safety rules for certain ATR airplanes to check more parts for problems and stop using some unsafe seat tracks. This affects ATR42 and ATR72 models and means more inspections and limits on part installations. Comments are open until January 4, 2027, so airlines and maintenance crews should get ready for these changes that keep flying safe without breaking the bank.