FAA Adds Airbus Helicopter Servo-Control Checks and Reporting Rules
Published Date: 11/20/2026
Rule
Summary
If you own or operate certain Airbus helicopters, the FAA has updated safety rules to keep your ride safe. They’re asking for extra checks on the main rotor servo-controls to make sure everything’s tight and secure, plus some reports sent back to the manufacturer. These new rules kick in December 28, 2026, so get ready to inspect and fix if needed—keeping your chopper flying smooth and safe without surprise costs.
Analyzed Economic Effects
4 provisions identified: 0 benefits, 4 costs, 0 mixed.
Possible repairs or part replacements after inspections
Depending on inspection results, you may need corrective actions that can include inspecting thread condition ($85 labor), replacing a ball bearing end (labor $85 + parts $1,299 = $1,384), or replacing a main rotor servo-control (labor $85 + parts $41,039 per servo-control). Replacing all three MR servo-controls on one helicopter could cost up to $123,372 in parts plus labor.
One-time torque inspections and reporting required
If you own or operate the listed Airbus helicopter models, you must perform a one-time inspection of the tightening torque on each nut connecting the upper ball bearing end to all three main rotor (MR) servo-controls and report the results to Airbus Helicopters. The FAA estimates the inspection labor is 3 work-hours per helicopter (1 hour per MR servo-control) at $85/hour = $255 per helicopter, plus reporting estimated at 1 hour ($85). This AD affects 63 U.S.-registered helicopters and is effective December 28, 2026; reports must be submitted within 30 days after the inspection (or within 30 days after the AD effective date if the inspection was done earlier).
Mandatory reporting paperwork burden
You must report inspection results (including 'no findings') to Airbus Helicopters as required by the AD. The Paperwork Reduction Act information lists OMB Control Number 2120-0056 and estimates public reporting at approximately 1 hour per response (including review and data gathering). Reports must be submitted within 30 days after the inspection or within 30 days after the AD effective date if the inspection was done earlier.
No special flight permits allowed
Special flight permits under 14 CFR 21.197 and 21.199 are not allowed for the affected helicopters under this AD. That restriction is effective as of December 28, 2026.
Personalized for You
How does this regulation affect your finances?
Personalize government policy and PRIA will tell you what this federal register document means for your household, plus every other regulation we track. PRIA reads each provision against your financial profile to show you exactly what matters to your wallet.
Key Dates
Department and Agencies
Related Federal Register Documents
2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems
In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.
2026-13440, Enabling Supersonic Overland Flight
The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.
2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period
The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.
2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility
The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.
2025-04846, Extension of the Prohibition Against Certain Flights in the Territory and Airspace of Libya
The FAA is extending the ban on certain flights over Libya for three more years, until March 20, 2028. This affects U.S. airlines, commercial operators, and pilots with FAA certificates flying in Libyan airspace, due to ongoing safety risks. The rule also reminds everyone how to apply for special approvals or exemptions if needed.
2025-03853, Enforcement Policy Regarding “Drug and Alcohol Testing of Certificated Repair Station Employees Located Outside of the United States; Correction”
The FAA is giving repair stations outside the U.S. a break by delaying enforcement of new drug and alcohol testing rules until March 20, 2025. This means affected repair stations don’t have to worry about penalties if they aren’t fully following the updated rules just yet. The delay helps everyone get ready without rushing or extra costs.
Previous / Next Documents
Previous: 2026-23681, Reef Fish Fishery in the Gulf of America; 2026 Recreational Private Angling Component Closure for Red Snapper in Federal Waters off Texas
Starting November 21, 2026, private recreational anglers fishing for red snapper in federal waters off Texas will have to stop for the rest of the year. This temporary closure helps protect red snapper from being overfished and keeps the catch within safe limits. If you love fishing for red snapper near Texas, plan ahead and enjoy other spots or species!
Next: 2026-23685, Air Plan Approval; Kentucky; Campbell-Clermont Area Maintenance Plan for the 2010 1-Hour SO2 NAAQS; Withdrawal of Direct Final Rule
The EPA is pulling back its recent approval of Kentucky’s plan to keep sulfur dioxide pollution low in the Campbell-Clermont area because some folks didn’t agree with it. This means the plan won’t take effect on November 24, 2026, as planned. The EPA will review the comments and decide next steps, so residents and businesses in the area should stay tuned for updates.