Part 211: DEFINITIONS AND GENERAL PROVISIONS

Section 211.2010 End Sealing Compound Coat "End sealing compound coat" means a can coating applied to can ends which functions as a gasket when the end is assembled onto the can. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2030 Enhanced Under-the-Cup Fill "Enhanced under-the-cup fill" means an improved under-the-cup technique, such as use of Kartridg Pak Low Pressure Sequencing Springs in conjunction with process temperature gradient control, which forces most propellant which would oth…

Section 211.2035 Epoxy Polyamide Topcoat "Epoxy polyamide topcoat" means a coating used where harder films are required or in some areas where engraving is accomplished in camouflage colors. (Source: Added at 45 Ill. Reg. 3509, effective March 4, 2021)

Section 211.2040 Etching Filler "Etching filler" means, for purposes of 35 Ill. Adm. Code 218 and 219, a coating that contains less than 23 percent solids by weight and at least 0.50 percent acid by weight, and is used instead of applying a pretreatment coating followed by a prim…

Section 211.2050 Ethanol Blend Gasoline "Ethanol blend gasoline" means a mixture of gasoline and at least 9% ethanol by volume. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2055 Ethylene Propylenediene Monomer (EPDM) Roof Membrane "Ethylene propylenediene monomer roof membrane" or "EPDM roof membrane" means, for purposes of 35 Ill. Adm. Code 218 and 219, a prefabricated single sheet of elastomeric material composed of ethylene propylened…

Section 211.2070 Excess Air "Excess air" means air supplied in addition to the theoretical quantity necessary for complete combustion of all fuel and/or combustible waste material. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2080 Excess Emissions "Excess emissions" means any tonnage of NOx emailed by a NOx budget unit during a control period that exceeds the NOx allowances available for compliance deduction for the unit and for a control period. (Source: Added at 25 Ill. Reg. 108, effecti…

Section 211.2090 Excessive Release "Excessive release" means, for purposes of 35 Ill. Adm. Code 215.144, 218.144 and 219.144, a discharge of more than 295 g (0.65 lbs) of mercaptans and/or hydrogen sulfide into the atmosphere in any 5-minute period. (Source: Added at 17 Ill. Reg.…

Section 211.210 Actual Heat Input "Actual heat input" means the quantity of heat produced by the combustion of fuel using the gross heating value of the fuel. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2110 Existing Grain-Drying Operation (Repealed) (Source: Repealed at 20 Ill. Reg. 7590, effective May 22, 1996)

Section 211.2130 Existing Grain-Handling Operation (Repealed) (Source: Repealed at 20 Ill. Reg. 7590, effective May 22, 1996)

Section 211.2150 Exterior Base Coat "Exterior base coat" means a can coating applied to the exterior of a two-piece can body to provide protection to the metal or to provide background for any lithographic or printing operation. (Source: Added at 17 Ill. Reg. 16504, effective Sep…

Section 211.2170 Exterior End Coat "Exterior end coat" means a can coating applied to the exterior end of a can to provide protection to the metal. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2180 Exterior Primer for Large Commercial Aircraft "Exterior primer for large commercial aircraft" means an aerospace primer, applied to an aircraft of more than 110,000 pounds maximum certified take-off weight, manufactured for non-military use. (Source: Added at 45 …

Section 211.2190 External Floating Roof "External floating roof" means a cover over an open top storage tank consisting of a double deck or pontoon single deck which rests upon and is supported by the volatile organic liquid being contained and is equipped with a closure seal or …

Section 211.2200 Extreme High-Gloss Coating "Extreme high-gloss coating" means: For purposes of 35 Ill. Adm. Code 218.204(q)(1) regarding metal parts and products coatings, a coating that, when tested by ASTM D 523-80, incorporated by reference in Section 211.101 of this Part, sh…

Section 211.2210 Extreme Performance Coating "Extreme performance coating" means: Except for purposes of 35 Ill. Adm. Code 218.204(q) or 219.204(q), any coating that during intended use is exposed to any or all of the following: ambient weather conditions, temperatures consistent…

Section 211.2230 Fabric Coating "Fabric coating" means any protective, decorative or functional coating which is applied onto or impregnated into a textile fabric which is delivered to the coating line as a roll, unwound and coated as a continuous substrate. (Source: Added at 17 …

Section 211.2250 Fabric Coating Line "Fabric coating line" means a coating line in which any protective, decorative, or functional coating is applied onto or impregnated into a textile fabric which is delivered to the coating line as a roll, unwound and coated as a continuous sub…

Section 211.2270 Federally Enforceable Limitations and Conditions "Federally enforceable limitations and conditions" means all limitations and conditions which are enforceable by the Administrator of the USEPA, including those requirements developed pursuant to 40 CFR Parts 60 an…

Section 211.2285 Feed Mill "Feed mill" means a source or equipment at a source that produces food, including premixes, supplements and concentrates, for animal (non-human) consumption from grain, grain byproducts, or alfalfa and other ingredients, without cooking, but not includi…

Section 211.2290 Fermentation Time "Fermentation time" means the time elapsed between adding yeast to the dough and placing the product into the oven, expressed in hours to the nearest one-tenth hour. (Source: Added at 19 Ill. Reg. 6823, effective May 9, 1995)

Section 211.230 Adhesive "Adhesive" means any substance or mixture of substances intended to serve as a joining compound. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2300 Fill "Fill", for purposes of 35 Ill. Adm. Code 218.119 through 218.129 and 219.119 through 219.129, means the introduction of VOL into a storage vessel but not necessarily to complete capacity. (Source: Added at 18 Ill. Reg. 16929, effective November 15, 1994)

Section 211.2310 Final Repair Coat "Final repair coat" means: With respect to automobile or light-duty truck assembly or manufacturing described in 35 Ill. Adm. Code 218.204(a)(1) and 218.219(a)(1), a coating that is used to repaint topcoat that is damaged during vehicle assembly…

Section 211.2320 Finish Primer Surfacer "Finish primer surfacer" means, for purposes of 35 Ill. Adm. Code 218 and 219, a coating applied with a wet film thickness of less than 10 mils prior to the application of a topcoat for purposes of providing corrosion resistance, adhesion o…

Section 211.233 Adhesion Primer "Adhesion primer" means, for purposes of 35 Ill. Adm. Code 218 and 219, a coating that is applied to a polyolefin part to promote the adhesion of a subsequent coating. An adhesion primer should be clearly identified as an adhesion primer or adhesio…

Section 211.2330 Firebox "Firebox" means the chamber or compartment of a boiler or furnace in which materials are burned, but not the combustion chamber or afterburner of an incinerator. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.234 Adhesive Bonding Primer "Adhesive bonding primer" means a primer applied in a thin film to aerospace components for the purpose of corrosion inhibition and increased adhesive bond strength by attachment. There are two categories of adhesive bonding primers: primer…

Section 211.2340 Fire-Resistant Interior Coating "Fire-resistant interior coating" means: for civilian aircraft, fire-resistant interior coatings used on passenger cabin interior parts that are subject to the Federal Aviation Administration fireworthiness requirements; for milita…

Section 211.235 Adhesive Primer "Adhesive primer" means, for purposes of 35 Ill. Adm. Code 218 and 219, any product applied to a substrate, prior to the application of an adhesive, to provide a bonding surface. (Source: Added at 34 Ill. Reg. 14119, effective September 14, 2010)

Section 211.2350 Fixed-Roof Tank "Fixed-roof tank" means a cylindrical shell with a permanently affixed roof. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2355 Flare "Flare" means an open combustor without enclosure or shroud. (Source: Added at 33 Ill. Reg. 13326, effective August 31, 2009)

Section 211.2357 Flat Glass "Flat glass" means, for purposes of Part 217, glass made of soda-lime recipe and produced into continuous flat sheets and other products listed in Standard Industrial Classification 3211. (Source: Added at 33 Ill. Reg. 13326, effective August 31, 2009)

Section 211.2358 Flat Wood Paneling "Flat Wood Paneling" means natural finish hardwood plywood panels, hardwood panels with Class II finishes, tileboard, exterior siding, and printed interior panels made of hardwood plywood or thin particleboard. (Source: Amended at 35 Ill. Reg. …

Section 211.2359 Flat Wood Paneling Coating Line "Flat Wood Paneling Coating Line" means a coating line in which any protective, decorative, or functional coating is applied to flat wood paneling. (Source: Added at 34 Ill. Reg. 9069, effective June 25, 2010)

Section 211.2360 Flexible Coating "Flexible coating" means: Prior to May 1, 2012, a paint with the ability to withstand dimensional changes. On and after May 1, 2012, a coating that is required to comply with engineering specifications for impact resistance, mandrel bend, or elon…

Section 211.2365 Flexible Operation Unit "Flexible operation unit" means a chemical manufacturing process unit that manufactures different chemical products periodically by alternating raw materials or operating conditions. (Source: Added at 19 Ill. Reg. 6823, effective May 9, 19…

Section 211.2368 Flexible Packaging "Flexible Packaging" means any package or part of a package, the shape of which can be readily changed. Flexible packaging includes, but is not limited to, bags, pouches, liners, and wraps utilizing paper, plastic, film, aluminum foil, metalize…

Section 211.2369 Flexible Vinyl "Flexible vinyl" means, for purposes of 35 Ill. Adm. Code 218 and 219, non-rigid polyvinyl chloride plastic with a 5 percent by weight plasticizer content. (Source: Added at 34 Ill. Reg. 14119, effective September 14, 2010)

Section 211.2370 Flexographic Printing "Flexographic printing" means a roll printing technique in which the pattern to be applied is raised above the printing roll and the image carrier is made of rubber or other elastomeric materials. (Source: Added at 17 Ill. Reg. 16504, effect…

Section 211.2390 Flexographic Printing Line "Flexographic printing line" means a printing line performing flexographic printing. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.240 Adhesion Promoter "Adhesion promoter" means a coating used to promote adhesion of a topcoat on surfaces such as trim moldings, door locks and door sills, where sanding is impractical. (Source: Added at 19 Ill. Reg. 6823, effective May 9, 1995)

Section 211.2400 Flight Test Coating "Flight test coating" means a coating applied to aircraft other than missiles or single-use aircraft prior to flight testing to protect the aircraft from corrosion and to provide required marking during flight test evaluation. (Source: Added a…

Section 211.2410 Floating Roof "Floating roof" means a roof on a stationary tank, reservoir, or other container which moves vertically upon change in volume of the stored material. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.2412 Flush Cleaning at Aerospace Facilities "Flush cleaning at aerospace facilities" means removal of contaminants, such as dirt, grease, oil, and coatings, from an aerospace vehicle or component or from coating equipment by passing solvent over, into, or through the …