Illinois Administrative Code

Section 211.4768 Pleasure Craft "Pleasure craft" means, for purposes of 35 Ill. Adm. Code 218 and 219, a vessel that is manufactured or operated primarily for recreational purposes, or leased, rented, or chartered to a person or business for recreational purposes. (Source: Added …

Section 211.4769 Pleasure Craft Surface Coating "Pleasure craft surface coating" means, for purposes of 35 Ill. Adm. Code 218 and 219, any coating, except unsaturated polyester resin (fiberglass) coatings, containing volatile organic materials and applied by brush, spray, roller,…

Section 211.4770 PM-10 "PM-10" means particulate matter with an aerodynamic diameter less than or equal to a nominal 10 micrometers, as measured by the applicable test methods specified by rule. Ambient air concentrations for PM-10 are usually expressed in micrograms per cubic me…

Section 211.479 Allowance "Allowance" means an authorization to emit up to one ton of NOx during the control period of a specified year or any year thereafter under 35 Ill. Adm. Code 217 and 40 CFR 96. (Source: Added at 25 Ill. Reg. 108, effective December 26, 2000)

Section 211.4790 Pneumatic Rubber Tire Manufacture "Pneumatic rubber tire manufacture" means the production of pneumatic rubber tires with a bead diameter up to but not including 20.0 inches and cross section dimension up to 12.8 inches, but not including specialty tires for anti…

Section 211.481 Ammunition Sealant "Ammunition Sealant" means, for purposes of 35 Ill. Adm. Code 218.204(q)(1) and 219.204(q)(1), a coating applied in the manufacture of ammunition, including cap sealants and mouth waterproofing sealants. (Source: Added at 34 Ill. Reg. 14119, eff…

Section 211.4810 Polybasic Organic Acid Partial Oxidation Manufacturing Process "Polybasic organic acid partial oxidation manufacturing process" means any process involving partial oxidation of hydrocarbons with air to manufacture polybasic acids or their anhydrides, such as male…

Section 211.4830 Polyester Resin Material(s) "Polyester resin material(s)" means gel coat and unsaturated polyester resin, such as isophthalic, orthophthalic, halogenated, bisphenol A, vinyl ester, or furan resins; cross-linking agents; catalysts; inhibitors; accelerators; promot…

Section 211.484 Animal "Animal" means any organism other than a human being of the kingdom, Animalia, distinguished from other multicellular organisms by certain typical characteristics such as the power of locomotion, fixed structure and limited growth, and non-photosynthetic me…

Section 211.485 Animal Pathological Waste "Animal pathological waste" means waste composed of whole or parts of animal carcasses and also noncarcass materials such as plastic, paper wrapping and animal collars. Noncarcass materials shall not exceed ten percent by weight of the to…

Section 211.4850 Polyester Resin Products Manufacturing Process "Polyester resin products manufacturing process" means a manufacturing process that fabricates or reworks products for commercial, military or industrial use by mixing, pouring, hand laying-up, impregnating, injectin…

Section 211.4870 Polystyrene Plant "Polystyrene plant" means any collection of process units and associated storage facilities at a source engaged in using styrene to manufacture polystyrene resin. (Source: Added at 17 Ill. Reg. 16504 effective September 27, 1993)

Section 211.4890 Polystyrene Resin "Polystyrene resin" means a substance consisting of styrene polymer and additives which is manufactured at a polystyrene plant. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.4895 Polyvinyl Chloride Plastic (PVC Plastic) "Polyvinyl chloride plastic" or "PVC plastic" means, for purposes of 35 Ill. Adm. Code 218 and 219, a polymer of the chlorinated vinyl monomer that contains 57 percent or more chlorine. (Source: Added at 34 Ill. Reg. 14119…

Section 211.490 Annual Grain Through-Put "Annual grain through-put" unless otherwise shown by the owner or operator, annual grain through-put for grain-handling operations, which have been in operation for three consecutive years prior to June 30, 1975, shall be determined by add…

Section 211.4900 Porous Material "Porous material" means, for purposes of 35 Ill. Adm. Code 218 and 219, a substance that has tiny openings, often microscopic, in which fluids may be absorbed or discharged, including, but not limited to, paper and corrugated paperboard. Porous ma…

Section 211.491 Antichafe Coating "Antichafe coating" means a coating applied to areas of moving aerospace components that may rub during normal operations or installation. (Source: Added at 45 Ill. Reg. 3509, effective March 4, 2021)

Section 211.4910 Portable Grain-Handling Equipment "Portable grain-handling equipment" means any equipment (excluding portable grain dryers) that is designed and maintained to be movable primarily for use in a non-continuous operation for loading and unloading one-turn storage sp…

Section 211.492 Antifoulant Coating "Antifoulant coating" means, for purposes of 35 Ill. Adm. Code 218 and 219, any coating applied to the underwater portion of a pleasure craft to prevent or reduce the attachment of biological organisms, and registered with USEPA as a pesticide …

Section 211.493 Antifouling Sealer/Tie Coat "Antifouling Sealer/Tie Coat" means a coating applied over biocidal antifouling coating for the purpose of preventing release of biocides into the environment and/or to promote adhesion between an antifouling and a primer or other antif…

Section 211.4930 Portland Cement Manufacturing Process Emission Source "Portland cement manufacturing process emission source" means any items of process equipment or manufacturing processes used in or associated with the production of portland cement, including, but not limited …

Section 211.495 Anti-Glare/Safety Coating "Anti-glare/safety coating" means a low gloss coating formulated to minimize glare for safety purposes on interior surfaces of a vehicle, as specified under the U.S. Department of Transportation Motor Vehicle Safety Standards. (Source: Ad…

Section 211.4950 Portland Cement Process or Portland Cement Manufacturing Plant "Portland cement process" or "Portland cement manufacturing plant" means any facility or plant manufacturing portland cement by either the wet or dry process. (Source: Added at 17 Ill. Reg. 16504, eff…

Section 211.4960 Potential Electrical Output Capacity "Potential electrical output capacity" means the MWe capacity rating for the units which shall be equal to 33% of the maximum design heat input capacity of the steam generating unit. (Source: Added at 25 Ill. Reg. 108, effecti…

Section 211.4970 Potential to Emit "Potential to emit (PTE)" means the maximum capacity of a stationary source to emit any air pollutant under its physical and operational design. Any physical or operational limitation on the capacity of a source to emit an air pollutant, includi…

Section 211.4990 Power Driven Fastener Coating "Power driven fastener coating" means the coating of nail, staple, brad and finish nail fasteners where such fasteners are fabricated from wire or rod of 0.0254 inch diameter or greater, where such fasteners are bonded into coils or …

Section 211.500 Antique Aerospace Vehicle or Component "Antique aerospace vehicle or component" means an aircraft or a component of an aircraft that is at least 30 years old and is not routinely in commercial or military service in the capacity for which it was designed. (Source:…

Section 211.5010 Precoat "Precoat" means any coating which is applied to bare metal primarily to deactivate the metal surface for corrosion resistance to a subsequent water-base primer. (Source: Added at 19 Ill. Reg. 6823, effective May 9, 1995)

Section 211.5012 Prefabricated Architectural Coatings "Prefabricated architectural coatings" means, for purposes of 35 Ill. Adm. Code 218 and 219, coatings applied to metal parts and products that are to be used as an architectural structure. (Source: Added at 34 Ill. Reg. 14119,…

Section 211.5015 Preheater Kiln "Preheater kiln" means, for the purposes of 35 Ill. Adm. Code 217, Subpart T, a kiln where the feed to the kiln is preheated in cyclone chambers prior to the final reactions in a kiln which forms clinker. (Source: Added at 25 Ill. Reg. 4582, effect…

Section 211.5020 Preheater/Precalciner Kiln "Preheater/precalciner kiln" means, for the purposes of 35 Ill. Adm. Code 217, Subpart T, a kiln where the feed to the kiln is preheated in cyclone chambers and utilizes a second burner to calcine material in a separate vessel attached …

Section 211.5030 Pressure Release "Pressure release" means the emission of materials resulting from system pressure being greater than set pressure of the pressure relief device. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.5050 Pressure Tank "Pressure tank" means a tank in which fluids are stored at a pressure greater than atmospheric pressure. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.5060 Pressure/Vacuum Relief Valve "Pressure/vacuum relief valve" means a device affixed to the storage tank vent pipe to prevent the escape or intrusion of gases. (Source: Added at 18 Ill. Reg. 14962, effective September 21, 1994)

Section 211.5061 Pretreatment Coating "Pretreatment coating" means, for purposes of 35 Ill. Adm. Code 218 and 219, a coating that contains no more than 12 percent solids by weight and at least 0.50 percent acid by weight, is used to provide surface etching, and is applied directl…

Section 211.5062 Pretreatment Wash Primer "Pretreatment wash primer" means: For purposes of Subparts HH of 35 Ill. Adm. Code 218 and 219, the first coating applied to bare metal if solventborne primers will be applied. This coating contains a minimum of 0.5 percent acid, by weigh…

Section 211.5065 Primary Product "Primary Product" means a product of a chemical manufacturing process unit that shall be determined according to the procedures specified as follows: a) If a chemical manufacturing process unit produces more than one intended chemical product, the…

Section 211.5070 Prime Coat "Prime coat" means the first of two or more coatings applied to a substrate in a multiple coat operation. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.5072 Primer for General Aviation Rework Facility "Primer for general aviation rework facility" means an aerospace primer applied at a general aviation rework facility. (Source: Added at 45 Ill. Reg. 3509, effective March 4, 2021)

Section 211.5075 Primer Sealant "Primer sealant" means, for purposes of 35 Ill. Adm. Code 218.204(q) and 219.204(q), a sealant applied in the manufacture of ammunition to assembled primers to maintain the primer assembly and prevent explosive priming mix from dusting during the t…

Section 211.5080 Primer Sealer "Primer sealer" means an undercoat that improves the adhesion of the topcoat, provides corrosion resistance, and promotes color uniformity. (Source: Added at 19 Ill. Reg. 6823, effective May 9, 1995)

Section 211.5090 Primer Surfacer Coat "Primer surfacer coat" means, for purposes of 35 Ill. Adm. Code 215.204(a), 218.204(a)(1), and 219.204(a)(1), a coating used to touch up areas on the surface of automobile or light-duty truck bodies not adequately covered by the prime coat be…

Section 211.510 Application Area "Application area" means an area where a coating is applied by dipping, spraying or other techniques. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.5110 Primer Surfacer Operation "Primer surfacer operation" means the application area(s), flashoff area(s) and oven(s) that are used to apply and dry or cure primer surfacer coat on a single assembly line. (Source: Added at 17 Ill. Reg. 16504, effective September 27, …

Section 211.5130 Primers "Primers" means any coatings formulated and applied to substrates to provide a firm bond between the substrate and subsequent coats. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)

Section 211.5140 Printed Interior Panel "Printed Interior Panel" mean a panel whose grain or natural surface is obscured by fillers and basecoats upon which a simulated grain or decorative pattern is printed. (Source: Added at 35 Ill. Reg. 13451, effective July 27, 2011)

Section 211.5150 Printing "Printing" means the application of words, designs, pictures, or other images to a substrate using ink. (Source: Added at 17 Ill. Reg. 16504, effective September 27, 1993)