Illinois Administrative Code

Section 219.425 Recordkeeping for Leaks a) The owner or operator of a synthetic organic chemical or polymer manufacturing plant shall maintain a leaking components monitoring log which shall contain, at a minimum, the following information: 1) The name of the process unit where t…

Section 219.426 Report for Leaks The owner or operator of a synthetic organic chemical or polymer manufacturing plant subject to Section 219.421 through 219.430 of this Part shall: a) Submit quarterly reports to the Agency on or before March 31, June 30, September 30, and Decembe…

Section 219.427 Alternative Program for Leaks The Agency shall approve an alternative program of monitoring, recordkeeping, or reporting to that prescribed in this Subpart upon a demonstration by the owner or operator of such plant that the alternative program will provide source…

Section 219.428 Open-Ended Valves a) Each open-ended valve shall be equipped with a cap, blind flange, plug, or a second valve, except during operations requiring fluid flow through the open-ended valve. b) Each open-ended valve equipped with a second valve shall be operated in a…

Section 219.429 Standards for Control Devices Control devices used to comply with Section 219.428(c) of this Part shall comply with the following: a) If the control device is a vapor recovery system (for example, condensers and adsorbers), it shall be designed and operated to rec…

Section 219.430 Compliance Date (Repealed) (Source: Repealed at 17 Ill. Reg. 16918, effective September 27, 1993)

Section 219.431 Applicability a) The provisions of Sections 219.431 through 219.436 of this Subpart shall apply to every owner or operator of any chemical manufacturing process unit that manufactures, as a primary product, one or more of the chemicals listed in Appendix A of this…

Section 219.432 Control Requirements a) Every owner or operator of a source subject to the requirements of this Subpart, as determined by Section 219.431 of this Subpart, shall either: 1) Reduce emissions of VOM, less methane or ethane, by 98 weight-percent, or to 20 ppmv, on a d…

Section 219.433 Performance and Testing Requirements a) For the purpose of demonstrating compliance with the TRE index value in Section 219.432(c) of this Subpart, an engineering assessment shall be made to determine process vent stream flow rate, net heating value, and VOM emiss…

Section 219.434 Monitoring Requirements a) The owner or operator of a source subject to the control requirements in Section 219.432 of this Subpart that uses an incinerator to comply with the VOM emission limitation specified in Section 219.432(a)(1) shall install, calibrate, mai…

Section 219.435 Recordkeeping and Reporting Requirements a) Every owner or operator of a reactor or distillation unit with a TRE index value of 4.0 or less shall keep records, for a minimum of 3 years, of the following parameters measured during a performance test or TRE determin…

Section 219.436 Compliance Date Every owner or operator of an source subject to Sections 219.431, 219.432, 219.433, 219.434 or 219.435 of this Subpart shall comply with its standards, limitations and mandates by March 15, 1996. (Source: Added at 19 Ill. Reg. 6958, effective May 9…

Section 219.441 Petroleum Refinery Waste Gas Disposal a) Except as provided in subsection (b) or (c) of this Section, no person shall cause or allow the discharge of organic materials in excess of 100 ppm equivalent methane (molecular weight 16.0) into the atmosphere from: 1) Any…

Section 219.442 Vacuum Producing Systems No owner or operator of a petroleum refinery shall cause or allow the operation of any vacuum producing system unless the condensers, hot wells and accumulators of any such system are equipped with vapor loss control equipment including, b…

Section 219.443 Wastewater (Oil/Water) Separator No owner or operator of a petroleum refinery shall operate any wastewater (oil/water) separator at a petroleum refinery unless the separator is equipped with air pollution control equipment capable of reducing by 85 percent or more…

Section 219.444 Process Unit Turnarounds a) No owner or operator of a petroleum refinery shall cause or allow a refinery process unit turnaround except in compliance with an operating procedure as approved by the Agency. b) Unless a procedure was already on file with the Agency a…

Section 219.445 Leaks: General Requirements The owner or operator of a petroleum refinery shall: a) Develop a monitoring program plan consistent with the provisions of Section 219.446 of this Part; b) Conduct a monitoring program consistent with the provisions of Section 219.447 …

Section 219.446 Monitoring Program Plan for Leaks The owner or operator of a petroleum refinery shall prepare a monitoring program plan which contains, at a minimum: a) An identification of all refinery components and the period in which each will be monitored pursuant to Section…

Section 219.447 Monitoring Program for Leaks a) The owner or operator of a petroleum refinery subject to Section 219.445 of this Part shall, for the purpose of detecting leaks, conduct a component monitoring program consistent with the following provisions: 1) Test once between M…

Section 219.448 Recordkeeping for Leaks a) The owner or operator of a petroleum refinery shall maintain a leaking components monitoring log which shall contain, at a minimum, the following information: 1) The name of the process unit where the component is located; 2) The type of…

Section 219.449 Reporting for Leaks The owner or operator of a petroleum refinery shall: a) Submit a report to the Agency prior to the 1st day of both July and September listing all leaking components identified pursuant to Section 219.447 of this Part but not repaired within 22 …

Section 219.450 Alternative Program for Leaks The Agency may approve an alternative program of monitoring, recordkeeping or reporting to that prescribed in Sections 219.446 through 219.449 of this Part upon a demonstration by the owner or operator of a petroleum refinery that the…

Section 219.451 Sealing Device Requirements Except for safety pressure relief valves, no owner or operator of a petroleum refinery shall install or operate a valve at the end of a pipe or line containing volatile organic materials unless the pipe or line is sealed with a second v…

Section 219.452 Compliance Schedule for Leaks The owner or operator of a petroleum refinery shall adhere to the increments of progress contained in the following schedule: a) Submit to the Agency a monitoring program consistent with Section 219.446 of this Part prior to July 1, 1…

Section 219.453 Compliance Dates (Repealed) (Source: Repealed at 17 Ill. Reg. 16918, effective September 27, 1993) SUBPART S: RUBBER AND MISCELLANEOUS PLASTIC PRODUCTS

Section 219.461 Manufacture of Pneumatic Rubber Tires The owner or operator of an undertread cementing, treadend cementing or bead dipping operation at a pneumatic rubber tire manufacturing source shall install and operate: a) A capture system, with minimum capture efficiency of …

Section 219.462 Green Tire Spraying Operations The owner or operator of a green tire spraying operation at a pneumatic rubber tire manufacturing source shall: a) Install and operate: 1) A capture system with a minimum capture efficiency of 90 percent by weight of VOM; and 2) A co…

Section 219.463 Alternative Emission Reduction Systems In lieu of complying with Section 219.461 or 219.462 of this Part, the owner or operator of an source may utilize an alternative volatile organic emission reduction system, including an alternative production process, which i…

Section 219.464 Emission Testing a) Upon a reasonable request by the Agency, the owner or operator of a VOM source required to comply with a limit of Sections 219.461 through 219.464 of this Part shall conduct emissions testing, at such person's own expense, to demonstrate compli…

Section 219.465 Compliance Dates (Repealed) (Source: Repealed at 17 Ill. Reg. 16918, effective September 27, 1993)

Section 219.466 Compliance Plan (Repealed) (Source: Repealed at 17 Ill. Reg. 16918, effective September 27, 1993) SUBPART T: PHARMACEUTICAL MANUFACTURING

Section 219.480 Applicability a) The rules of this Subpart, except for Sections 219.483 through 219.485 of this Part, apply to all emission units of VOM, including but not limited to reactors, distillation units, dryers, storage tanks for VOL, equipment for the transfer of VOL, f…

Section 219.481 Control of Reactors, Distillation Units, Crystallizers, Centrifuges and Vacuum Dryers a) The owner or operator shall equip all reactors, distillation units, crystallizers, centrifuges and vacuum dryers that are used to manufacture pharmaceuticals with surface cond…

Section 219.482 Control of Air Dryers, Production Equipment Exhaust Systems and Filters a) The owner or operator of an air dryer or production equipment exhaust system used to manufacture pharmaceuticals shall control the emissions of VOM from such emission units by air pollution…

Section 219.483 Material Storage and Transfer The owner or operator of a pharmaceutical manufacturing source shall: a) Provide a vapor balance system that is at least 90 percent effective in reducing VOM emissions from truck or railcar deliveries to storage tanks with capacities …

Section 219.484 In-Process Tanks The owner or operator shall install covers on all in-process tanks used to manufacture pharmaceuticals and containing a VOL at any time. These covers must remain closed, except as production, sampling, maintenance or inspection procedures require …

Section 219.485 Leaks The owner or operator of a pharmaceutical manufacturing source shall repair any component from which a leak of VOL can be observed. The repair shall be completed as soon as practicable but no later than 15 days after the leak is found. If the leaking compone…

Section 219.486 Other Emission Units The owner or operator of a washer, laboratory hood, tablet coating operation, mixing operation or any other process emission unit not subject to Section 219.481 through 219.485 of this Part, and used to manufacture pharmaceuticals shall contro…

Section 219.487 Testing a) Upon request by the Agency or the USEPA, the owner or operator of any VOM source subject to this Subpart or exempt from this Subpart by virtue of the provisions of Section 219.480 of this Part shall, at his own expense, demonstrate compliance to the Age…

Section 219.488 Monitoring for Air Pollution Control Equipment a) At a minimum, continuous monitors for the following parameters shall be installed on air pollution control equipment used to control sources subject to this Subpart: 1) Destruction device combustion temperature. 2)…

Section 219.489 Recordkeeping for Air Pollution Control Equipment a) The owner or operator of a pharmaceutical manufacturing source shall maintain the following records: 1) Parameters listed in Section 219.488(a) of this Part shall be recorded. 2) For emission units subject to Se…

Section 219.500 Applicability for Batch Operations a) The control requirements set forth in Section 219.501 of this Subpart shall apply to process vents associated with batch operations at sources identified by any of the following four-digit standard industrial classification ("…

Section 219.501 Control Requirements for Batch Operations a) Every owner or operator of a single unit operation with an average flow rate, as determined in accordance with Section 219.502(b) of this Subpart, below the flow rate value calculated by the applicability equations cont…

Section 219.502 Determination of Uncontrolled Total Annual Mass Emissions and Actual Weighted Average Flow Rate Values for Batch Operations a) Uncontrolled total annual mass emissions shall be determined by the following methods: 1) Direct process vent emissions measurements take…

Section 219.503 Performance and Testing Requirements for Batch Operations a) Upon the Agency's request, the owner or operator of a batch operation shall conduct testing to demonstrate compliance with Section 219.501 of this Subpart. The owner or operator shall, at its own expense…

Section 219.504 Monitoring Requirements for Batch Operations a) Every owner or operator using an afterburner to comply with Section 219.501 of this Subpart shall install, calibrate, maintain and operate, according to manufacturer's specifications, temperature monitoring devices w…

Section 219.505 Reporting and Recordkeeping for Batch Operations a) Every owner or operator of a de minimis single unit operation or batch process train exempt under Section 219.500(c)(1) or (c)(2) of this Subpart shall keep records of the uncontrolled total annual mass emissions…