5,005 sections in this chapter.
225 ILCS 705/26.11 Sec. 26.11
0.5K chars
(225 ILCS 705/26.11) (from Ch. 96 1/2, par. 2611) Sec. 26.11. At every underground landing where men enter or leave the cage and where men must pass from one side of the cage to the other there shall be a safe passageway, free from obstruction and dry as possible around the shaft…
225 ILCS 705/26.12 Sec. 26.12
0.7K chars
(225 ILCS 705/26.12) (from Ch. 96 1/2, par. 2612) Sec. 26.12. No accumulation of ice or obstructions of any kind shall be permitted in any shaft in which men are hoisted or lowered; nor shall any dangerous gases or steam be discharged into the shaft in such quantities or at such …
225 ILCS 705/26.13 Sec. 26.13
0.5K chars
(225 ILCS 705/26.13) (from Ch. 96 1/2, par. 2613) Sec. 26.13. All hoisting shafts, air shafts, and escapement shafts constructed after March, 1910, shall be of fireproof construction, and if poured concrete is used in said construction it shall be not less than 6 inches in thickn…
225 ILCS 705/26.14 Sec. 26.14
0.4K chars
(225 ILCS 705/26.14) (from Ch. 96 1/2, par. 2614) Sec. 26.14. The roof and walls of the passageway leading from the bottom of the hoisting shaft and the air and escapement shaft designated as such under the law, within a distance of 300 feet from the bottom of either of said shaf…
225 ILCS 705/26.15 Sec. 26.15
0.2K chars
(225 ILCS 705/26.15) (from Ch. 96 1/2, par. 2615) Sec. 26.15. Shafts shall be equipped with self-closing or manually controlled safety gates at surface landings. (Source: Laws 1953, p. 701.)
225 ILCS 705/26.16 Sec. 26.16
0.4K chars
(225 ILCS 705/26.16) (from Ch. 96 1/2, par. 2616) Sec. 26.16. Positive derails shall be placed on tracks leading to shafts to prevent cars, motors, etc. from going into the shaft when the cage is not at the landing. The provisions of this section shall not apply to "slope" or "dr…
225 ILCS 705/27.01 Sec. 27.01
0.6K chars
(225 ILCS 705/27.01) (from Ch. 96 1/2, par. 2701) Sec. 27.01. In all mines in this State which are classified as gassy by the State Mine Inspector, and where coal is broken down by the use of explosives, a sufficient number of first class miners, who are citizens of the United St…
225 ILCS 705/27.02 Sec. 27.02
0.7K chars
(225 ILCS 705/27.02) (from Ch. 96 1/2, par. 2702) Sec. 27.02. In all mines in this State which are classified as non-gassy by the State Mine Inspector, and where coal is broken down by the use of explosives, a sufficient number of first-class miners, who are citizens of the Unite…
225 ILCS 705/27.03 Sec. 27.03
0.5K chars
(225 ILCS 705/27.03) (from Ch. 96 1/2, par. 2703) Sec. 27.03. This Act shall not be construed to prohibit the breaking down of coal while men are in the mine if such breaking down is accomplished by compressed air or by some mechanical or chemical-mechanical device which does not…
225 ILCS 705/27.04 Sec. 27.04
0.8K chars
(225 ILCS 705/27.04) (from Ch. 96 1/2, par. 2704) Sec. 27.04. When the breaking down of coal is not done "on shift", and while men are in the mine, the drillers and shooters or shot firers shall immediately after the completion of their work, post a notice in a conspicuous place …
225 ILCS 705/27.05 Sec. 27.05
0.2K chars
(225 ILCS 705/27.05) (from Ch. 96 1/2, par. 2705) Sec. 27.05. In hand loading mines where the miners drill and prepare their own shots the practice may continue, provided it is approved by the State Mining Board. (Source: Laws 1953, p. 701.)
225 ILCS 705/29.01 Sec. 29.01
0.7K chars
(225 ILCS 705/29.01) (from Ch. 96 1/2, par. 2901) Sec. 29.01. In all mines adequate telephone service or equivalent 2-way communication facilities, including, but not limited to, 2-way text messages, shall be provided at the top and bottom of each main shaft or slope, and from th…
225 ILCS 705/29.02 Sec. 29.02
0.2K chars
(225 ILCS 705/29.02) (from Ch. 96 1/2, par. 2902) Sec. 29.02. Telephone lines, other than cables, shall be carried on insulators, and where they cross power or trolley wires they shall be insulated adequately. (Source: Laws 1953, p. 701.)
225 ILCS 705/29.03 Sec. 29.03
0.1K chars
(225 ILCS 705/29.03) (from Ch. 96 1/2, par. 2903) Sec. 29.03. All necessary repairs shall be made promptly. (Source: Laws 1953, p. 701.)
225 ILCS 705/29.04 Sec. 29.04
0.3K chars
(225 ILCS 705/29.04) (from Ch. 96 1/2, par. 2904) Sec. 29.04. Where telephone wires running from the top surface into the mine are used for telephone service, said lines shall be equipped with lightning arresters located above ground. (Source: Laws 1955, p. 2012.)
225 ILCS 705/29.05 Wireless emergency communication devices
1.5K chars
(225 ILCS 705/29.05) Sec. 29.05. Wireless emergency communication devices. A wireless emergency communication device approved by the Mining Board must be worn by each person underground. The operator shall provide these devices. The wireless emergency communication device must, a…
225 ILCS 705/29.06 Wireless tracking devices
1.6K chars
(225 ILCS 705/29.06) Sec. 29.06. Wireless tracking devices. A wireless tracking device approved by the Mining Board must be worn by each person underground. The operator shall provide these devices. The tracking device must be capable of providing real-time monitoring of the phys…
225 ILCS 705/29.07 Mine Technology Task Force; provision of rescue chambers and wireless devices
1.7K chars
(225 ILCS 705/29.07) Sec. 29.07. Mine Technology Task Force; provision of rescue chambers and wireless devices. (a) The Director shall establish a Mine Technology Task Force composed of representatives of an organization representing mine employees, coal operators, academia, and …
225 ILCS 41/30-1 Sec. 30-1
0.2K chars
(225 ILCS 41/30-1) (Section scheduled to be repealed on January 1, 2028) Sec. 30-1. This Act takes effect January 1, 1993. (Source: P.A. 87-966.)
225 ILCS 447/30-10 Qualifications for licensure as a locksmith
2.2K chars
(225 ILCS 447/30-10) (Section scheduled to be repealed on January 1, 2029) Sec. 30-10. Qualifications for licensure as a locksmith. (a) A person is qualified for licensure as a locksmith if the person meets all of the following requirements: (1) Is at least 18 years of age. (2) H…
225 ILCS 407/30-10 Rules
0.4K chars
(225 ILCS 407/30-10) (Section scheduled to be repealed on January 1, 2030) Sec. 30-10. Rules. The Department, after notifying and considering the recommendations of the Advisory Board, if any, shall adopt any rules that may be necessary for the administration, implementation and …
225 ILCS 407/30-13 The Division of Real Estate General Fund
1.3K chars
(225 ILCS 407/30-13) (Section scheduled to be repealed on January 1, 2030) Sec. 30-13. The Division of Real Estate General Fund. Prior to July 1, 2023, all of the fees, fines, and penalties collected under this Act shall be deposited into the General Professions Dedicated Fund. P…
225 ILCS 447/30-15 Sec. 30-15
5.6K chars
(225 ILCS 447/30-15) (Section scheduled to be repealed on January 1, 2029) Sec. 30-15. Qualifications for licensure as a locksmith agency. (a) Upon receipt of the required fee and proof that the applicant has a full-time Illinois licensed locksmith licensee-in-charge, which is a …
225 ILCS 454/30-15 Licensing of education providers; approval of courses
5.1K chars
(225 ILCS 454/30-15) (Section scheduled to be repealed on January 1, 2030) Sec. 30-15. Licensing of education providers; approval of courses. (a) (Blank). (b) (Blank). (c) (Blank). (d) (Blank). (e) (Blank). (f) All education providers shall submit, at the time of initial applicat…
225 ILCS 447/30-20 Training; locksmith and employees
1.5K chars
(225 ILCS 447/30-20) (Section scheduled to be repealed on January 1, 2029) Sec. 30-20. Training; locksmith and employees. (a) Registered employees of a licensed locksmith agency shall complete a minimum of 20 hours of training provided by a qualified instructor within 30 days of …
225 ILCS 454/30-20 Fees for education provider license; renewal; term
0.9K chars
(225 ILCS 454/30-20) (Section scheduled to be repealed on January 1, 2030) Sec. 30-20. Fees for education provider license; renewal; term. All applications for an education provider license shall be accompanied by a nonrefundable application fee in an amount established by rule. …
225 ILCS 447/30-25 Customer identification; record keeping
2.1K chars
(225 ILCS 447/30-25) (Section scheduled to be repealed on January 1, 2029) Sec. 30-25. Customer identification; record keeping. (a) A locksmith who bypasses, manipulates, or originates a first key by code for a device safeguarding an area where access is meant to be limited, whet…
225 ILCS 454/30-25 Licensing of education provider instructors
3.8K chars
(225 ILCS 454/30-25) (Section scheduled to be repealed on January 1, 2030) Sec. 30-25. Licensing of education provider instructors. (a) No person shall act as either a pre-license or continuing education instructor without possessing a valid pre-license or continuing education in…
225 ILCS 407/30-30 Auction Advisory Board
3.0K chars
(225 ILCS 407/30-30) (Section scheduled to be repealed on January 1, 2030) Sec. 30-30. Auction Advisory Board. (a) There is hereby created the Auction Advisory Board. The Advisory Board shall consist of 7 members and shall be appointed by the Secretary. In making the appointments…
225 ILCS 447/30-30 Consumer protection; required information for consumers
1.5K chars
(225 ILCS 447/30-30) (Section scheduled to be repealed on January 1, 2029) Sec. 30-30. Consumer protection; required information for consumers. (a) A licensee providing any locksmith services shall document on a work order, invoice, or receipt the name, address, and telephone num…
225 ILCS 447/30-35 Advertising
0.5K chars
(225 ILCS 447/30-35) (Section scheduled to be repealed on January 1, 2029) Sec. 30-35. Advertising. In addition to any requirements under Section 35-15, a licensed locksmith or locksmith agency shall include the licensee's name, the city and state of the address provided to the D…
225 ILCS 454/30-5 Licensing of real estate education providers and instructors
4.1K chars
(225 ILCS 454/30-5) (Section scheduled to be repealed on January 1, 2030) Sec. 30-5. Licensing of real estate education providers and instructors. (a) No person shall operate an education provider entity without possessing a valid and active license issued by the Department. Only…
225 ILCS 447/30-5 Exemptions; locksmith
2.7K chars
(225 ILCS 447/30-5) (Section scheduled to be repealed on January 1, 2029) Sec. 30-5. Exemptions; locksmith. The provisions of this Act do not apply to any of the following if the person performing the service does not hold himself or herself out as a locksmith: (1) Automobile ser…
225 ILCS 458/30-5 Savings provisions
2.0K chars
(225 ILCS 458/30-5) (Section scheduled to be repealed on January 1, 2032) Sec. 30-5. Savings provisions. (a) This Act is intended to replace the Real Estate Appraiser Licensing Act in all respects. (b) Beginning July 1, 2002, the rights, powers, and duties exercised by the Office…
225 ILCS 407/30-50 Contractual agreements
0.3K chars
(225 ILCS 407/30-50) (Section scheduled to be repealed on January 1, 2030) Sec. 30-50. Contractual agreements. The Department may enter into contractual agreements with third parties to carry out the provisions of this Act. (Source: P.A. 95-572, eff. 6-1-08.)
225 ILCS 407/30-55 Reciprocal agreements
0.5K chars
(225 ILCS 407/30-55) (Section scheduled to be repealed on January 1, 2030) Sec. 30-55. Reciprocal agreements. The Department shall have the authority to enter into reciprocal licensing agreements with the proper authority of a state, territory, or possession of the United States …
225 ILCS 407/30-7 Department; powers and duties
0.8K chars
(225 ILCS 407/30-7) (Section scheduled to be repealed on January 1, 2030) Sec. 30-7. Department; powers and duties. (a) The Department shall exercise the powers and duties prescribed by the Civil Administrative Code of Illinois for the administration of licensing acts and shall e…
225 ILCS 705/30.01 Sec. 30.01
0.4K chars
(225 ILCS 705/30.01) (from Ch. 96 1/2, par. 3001) Sec. 30.01. The operator of every mine shall see that necessary and proper supports are provided for the roof in all working places, and in all entries and air courses where men are required to travel to and from any working place…
225 ILCS 705/30.02 Sec. 30.02
0.4K chars
(225 ILCS 705/30.02) (from Ch. 96 1/2, par. 3002) Sec. 30.02. At or near working faces, each operator shall provide props, roof bolts, caps, or other timbers for the proper securing of all working places. Temporary safety props, jacks, roof bolts, or cross bars shall be set close…
225 ILCS 705/30.03 Sec. 30.03
0.2K chars
(225 ILCS 705/30.03) (from Ch. 96 1/2, par. 3003) Sec. 30.03. Timbers removed by mining machinery, blasting operations, or for any other reason, shall be promptly replaced for adequate protection. (Source: Laws 1953, p. 701.)
225 ILCS 705/30.04 Sec. 30.04
0.4K chars
(225 ILCS 705/30.04) (from Ch. 96 1/2, par. 3004) Sec. 30.04. Every employee exposed to hazards from falls of coal or rock shall examine the roof, rib, and face before starting work in a working place, unless such place has been examined by competent and experienced personnel jus…
225 ILCS 705/30.05 Sec. 30.05
0.2K chars
(225 ILCS 705/30.05) (from Ch. 96 1/2, par. 3005) Sec. 30.05. Loose top and overhanging or loose face shall be either taken down or properly timbered. (Source: Laws 1953, p. 701.)
225 ILCS 447/31-10 Qualifications for licensure as a fingerprint vendor
4.4K chars
(225 ILCS 447/31-10) (Section scheduled to be repealed on January 1, 2029) Sec. 31-10. Qualifications for licensure as a fingerprint vendor. (a) A person is qualified for licensure as a fingerprint vendor if the person meets all of the following requirements: (1) Is at least 18 y…
225 ILCS 447/31-15 Qualifications for licensure as a fingerprint vendor agency
4.2K chars
(225 ILCS 447/31-15) (Section scheduled to be repealed on January 1, 2029) Sec. 31-15. Qualifications for licensure as a fingerprint vendor agency. (a) Upon receipt of the required fee, compliance with subsection (e) of this Section, and proof that the applicant has a full-time I…
225 ILCS 447/31-20 Training; fingerprint vendor and employees
1.7K chars
(225 ILCS 447/31-20) (Section scheduled to be repealed on January 1, 2029) Sec. 31-20. Training; fingerprint vendor and employees. (a) Registered employees of a licensed fingerprint vendor agency shall complete a minimum of 20 hours of training provided by a qualified instructor …
225 ILCS 447/31-25 Customer identification; record keeping
1.1K chars
(225 ILCS 447/31-25) (Section scheduled to be repealed on January 1, 2029) Sec. 31-25. Customer identification; record keeping. A fingerprint vendor or fingerprint vendor agency shall document in the form of a work order when and where each and every fingerprint service is provid…
225 ILCS 447/31-30 Restrictions on firearms
0.6K chars
(225 ILCS 447/31-30) (Section scheduled to be repealed on January 1, 2029) Sec. 31-30. Restrictions on firearms. (a) Nothing in this Act or the rules adopted under this Act shall authorize a person licensed as a fingerprint vendor or any employee of a licensed fingerprint vendor …
225 ILCS 447/31-5 Exemptions
1.8K chars
(225 ILCS 447/31-5) (Section scheduled to be repealed on January 1, 2029) Sec. 31-5. Exemptions. (a) The provisions of this Act regarding fingerprint vendors do not apply to any of the following, if the person performing the service does not hold oneself out as a fingerprint vend…
225 ILCS 705/31.01 Sec. 31.01
0.5K chars
(225 ILCS 705/31.01) (from Ch. 96 1/2, par. 3101) Sec. 31.01. All active underground working places in a mine shall be ventilated by a current of air containing not less than 19.5% of oxygen, not more than 0.5% of carbon dioxide, and no harmful quantities of other noxious or pois…
225 ILCS 705/31.02 Sec. 31.02
0.7K chars
(225 ILCS 705/31.02) (from Ch. 96 1/2, par. 3102) Sec. 31.02. The quantity of air reaching the last open crosscut in any pair or set of entries shall not be less than 9,000 cubic feet a minute, except that the quantity of air reaching the last open crosscut in any pair or set of …