Chapter 24-02. Identification and Listing of Hazardous Waste

1. Timeframe. a. Each pump in light liquid service must be monitored monthly to detect leaks by the methods specified in subsection 2 of section 33.1-24-02-193, except as provided in subsections 4, 5, and 6. b. Each pump in light liquid service must be checked by visual inspectio…

1. Each compressor must be equipped with a seal system that includes a barrier fluid system and which prevents leakage of total organic emissions to the atmosphere, except as provided in subsections 8 and 9. 2. Each compressor seal system as required in subsection 1 must be: a. O…

1. Except during pressure releases, each pressure relief device in gas or vapor service must be operated with no detectable emissions, as indicated by an instrument reading of less than five hundred parts per million above background, as measured by the method specified in subsec…

1. Each sampling connection system must be equipped with a closed-purge, closed-loop, or closed-vent system. This system must collect the sample purge for return to the process or for routing to the appropriate treatment system. Gases displaced during filling of the sample contai…

1. Requirements. a. Each open-ended valve or line must be equipped with a cap, blind flange, plug, or a second valve. b. The cap, blind flange, plug, or second valve must seal the open end at all times except during operations requiring hazardous secondary material stream flow th…

1. Each valve in gas or vapor or light liquid service must be monitored monthly to detect leaks by the methods specified in subsection 2 of section 33.1-24-02-193 and must comply with subsections 2 through 5, except as provided in subsections 6, 7, and 8, and sections 33.1-24-02-…

devices in light liquid or heavy liquid service, and flanges and other connectors. 1. Pumps and valves in heavy liquid service, pressure relief devices in light liquid or heavy liquid service, and flanges and other connectors must be monitored within five days by the method speci…

1. Delay of repair of equipment for which leaks have been detected will be allowed if the repair is technically infeasible without a hazardous secondary material management unit shutdown. In such a case, repair of this equipment must occur before the end of the next hazardous sec…

1. The remanufacturer or other person that stores or treats the hazardous secondary material in hazardous secondary material management units using closed-vent systems and control devices subject to sections 33.1-24-02-180 through 33.1-24-02-199 shall comply with the provisions o…

service - Percentage of valves allowed to leak. 1. A remanufacturer or other person that stores or treats the hazardous secondary material subject to the requirements of section 33.1-24-02-187 may elect to have all valves within a hazardous secondary material management unit comp…

service - Skip period leak detection and repair. 1. A remanufacturer or other person that stores or treats the hazardous secondary material subject to the requirements of section 33.1-24-02-187 may elect for all valves within a hazardous secondary material management unit to comp…

1. Each remanufacturer or other person that stores or treats the hazardous secondary material subject to the provisions of sections 33.1-24-02-180 through 33.1-24-02-199 shall comply with the test methods and procedures requirements provided in this section. 2. Leak detection mon…

1. Remanufacturer or other person that stores or treats the hazardous secondary material. a. Each remanufacturer or other person that stores or treats the hazardous secondary material subject to the provisions of sections 33.1-24-02-180 through 33.1-24-02-199 shall comply with th…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

233

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

1. The requirements of sections 33.1-24-02-200 through 33.1-24-02-214 apply to tanks and containers that contain hazardous secondary materials excluded under the remanufacturing exclusion at subdivision z of subsection 1 of section 33.1-24-02-04, unless the tanks and containers a…

As used in sections 33.1-24-02-200 through 33.1-24-02-214, all terms not defined herein have the meaning given them in North Dakota Century Code chapter 23.1-04 and chapters 33.1-24-01 through 33.1-24-05 and section 33.1-24-05-451. 1. "Average volatile organic concentration or av…

1. This section applies to the management of hazardous secondary material in tanks and containers subject to sections 33.1-24-02-200 through 33.1-24-02-214. 2. The remanufacturer or other person that stores or treats the hazardous secondary material shall control air pollutant em…

1. Material determination procedure to determine average volatile organic (VO) concentration of a hazardous secondary material at the point of material origination. a. A remanufacturer or other person that stores or treats the hazardous secondary material shall determine the aver…

1. The provisions of this section apply to the control of air pollutant emissions from tanks for which subsection 2 of section 33.1-24-02-202 references the use of this section for such air emission control. 242 2. The remanufacturer or other person that stores or treats the haza…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

1. The provisions of this section apply to the control of air pollutant emissions from containers for which subsection 2 of section 33.1-24-02-202 references the use of this section for such air emission control. 2. General requirements. a. The remanufacturer or other person that…

1. This section applies to each closed-vent system and control device installed and operated by the remanufacturer or other person that stores or treats the hazardous secondary material to 263 control air emissions in accordance with standards of sections 33.1-24-02-200 through 3…

1. The remanufacturer or other person that stores or treats the hazardous secondary material shall inspect and monitor air emission control equipment used to comply with sections 33.1-24-02-200 through 33.1-24-02-214 in accordance with the applicable requirements specified in sec…

1. Each remanufacturer or other person that stores or treats the hazardous secondary material subject to requirements of sections 33.1-24-02-200 through 33.1-24-02-214 shall record and maintain the information specified in subsections 2 through 10, as applicable to the facility. …

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

270

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

33.1-24-02-214. [Reserved]. 271 APPENDIX I Representative Sampling Methods The methods and equipment used for sampling waste materials will vary with the form and consistency of the waste materials to be sampled. Samples collected using the sampling protocols listed below, for sa…

other person that stores or treats the hazardous secondary material perform this determination using direct measurement. The remanufacturer or other person that stores or treats the hazardous secondary material may choose one or more appropriate methods to analyze each collected …

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

cathode ray tube glass undergoing recycling. Used, broken cathode ray tubes are not solid wastes if they meet the following conditions: 1. Prior to processing. These materials are not solid wastes if they are destined for recycling and if they meet the following requirements: a. …

recycling. Used, intact cathode ray tubes exported for recycling are not solid wastes if they meet the notice and consent conditions of subdivision e of subsection 1 of section 33.1-24-02-25, and if they are not speculatively accumulated as defined in subdivision h of subsection …

reuse. 1. Cathode ray tube exporters who export used, intact cathode ray tubes for reuse shall send a notification to the department and the environmental protection agency. This notification may cover export activities extending over a twelve month or lesser period. a. The notif…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

CHAPTER 33.1-24-02 IDENTIFICATION AND LISTING OF HAZARDOUS WASTE Section 33.1-24-02-01 Purpose and Scope 33.1-24-02-02 Definition of Solid Waste 33.1-24-02-03 Definition of Hazardous Waste 33.1-24-02-04 Exclusions 33.1-24-02-05 Special Requirements for Hazardous Waste Generated b…

hazardous secondary materials. 1. The requirements of sections 33.1-24-02-33 through 33.1-24-02-42 apply to owners or operators of reclamation and intermediate facilities managing hazardous secondary materials excluded under subdivision y of subsection 1 of section 33.1-24-02-04,…

The terms defined in subsections 4, 6, 7, and 8 of section 33.1-24-05-75 have the same meaning in sections 33.1-24-02-33 through 33.1-24-02-42. History: Effective January 1, 2019. General Authority: NDCC 23.1-04-03; S.L. 2017, ch. 199, § 1 Law Implemented: NDCC 23.1-04-03, 23.1-0…

1. The cost estimates for closure. a. The owner or operator shall have a detailed written estimate, in current dollars, of the cost of disposing of any hazardous secondary material as listed or characteristic hazardous waste, and the potential cost of closing the facility as a tr…

In accordance with subparagraph f of paragraph 6 of subdivision y of subsection 1 of section 33.1-24-02-04, an owner or operator of a reclamation or intermediate facility shall have financial assurance as a condition of the exclusion as required under subdivision y of subsection …