Chapter 24-05. Standards for Treatment, Storage, and Disposal Facilities and for the Management of Specific Hazardous Wastes and Specific Types of Hazardous Waste Management Facilities

1. The owner or operator shall develop and follow a schedule and procedure for inspecting overfill controls. 2. The owner or operator shall inspect at least once each operating day data gathered from monitoring and leak detection equipment (for example, pressure or temperature ga…

Sections 33.1-24-05-1080 through 33.1-24-05-1099 applies to owners or operators of facilities that treat or store hazardous waste in containers under sections 33.1-24-06-45 through 33.1-24-06-85, except as provided in subsection 2 of section 33.1-24-05-950. History: Effective Jan…

Standards apply to the condition of the containers, to the compatibility of waste with the containers, and to the management of the containers. 1. Condition of containers. If a container holding hazardous waste is not in good condition (for example, it exhibits severe rusting or …

At least weekly, the owner or operator must inspect areas where containers are stored, looking for leaking containers and for deterioration of containers and the containment system caused by corrosion or other factors. History: Effective January 1, 2019. General Authority: NDCC 2…

1. Container storage areas must have a containment system that is designed and operated in accordance with subsection 2, except as provided otherwise in subsection 3. 2. The containment system must be designed and operated as follows: a. A base must underlie the containers that i…

Containers holding ignitable or reactive waste must be located at least fifteen meters [50 feet] from the facility's property line. The owner or operator must also follow the general requirements for ignitable or reactive wastes that are specified in subsection 1 of section 33.1-…

1. Incompatible wastes, or incompatible wastes and materials (see appendix III to chapter 33.1-24-05 for examples), must not be placed in the same container, unless subsection 2 of section 33.1-24-05-967 is complied with. 2. Hazardous waste must not be placed in an unwashed conta…

At closure, all hazardous waste and hazardous waste residues must be removed from the containment system. Remaining containers, liners, bases, and soil containing or contaminated with hazardous waste or hazardous waste residues must be decontaminated or removed. History: Effectiv…

The owner or operator shall manage all hazardous waste placed in a container in accordance with the requirements of sections 33.1-24-05-400 through 33.1-24-05-474. Under a standardized permit, the following control devices are permissible: thermal vapor incinerator, catalytic vap…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

systems. A tank system or secondary containment system from which there has been a leak or spill, or which is unfit for use, must be removed from service immediately, and the owner or operator shall satisfy the following requirements: 1. Cessation of use; prevent flow or addition…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

1. At closure of a tank system, the owner or operator shall remove or decontaminate all waste residues, contaminated containment system components (liners, etc.), contaminated soils, and structures and equipment contaminated with waste, and manage them as a hazardous waste, unles…

The requirements of sections 33.1-24-05-1100 through 33.1-24-05-1129 applies to owners or operators of facilities that treat or store hazardous waste in above ground or on ground tanks under sections 33.1-24-06-45 through 33.1-24-06-85, standardized permit, except as provided in …

Owners or operators must ensure that the foundation, structural support, seams, connections, and pressure controls (if applicable) are adequately designed and that the tank system has sufficient structural strength, compatibility with the wastes to be stored or treated, and corro…

system. 1. The owner or operator shall ensure that proper handling procedures are followed to prevent damage to a new tank system during installation. Before placing a new tank system or component in use an independent, qualified installation inspector or a qualified professional…

All new tanks and ancillary equipment must be tested for tightness before being placed into use. If a tank system is found not to be tight, all repairs necessary to remedy the leaks in the system must be performed prior to covering, enclosing, or placing the tank system into use.…

1. The owner or operator must support and protect ancillary equipment against physical damage and excessive stress due to settlement, vibration, expansion, or contraction. 2. The owner or operator must provide the type and degree of corrosion protection recommended by an independ…

To prevent the release of hazardous waste or hazardous constituents to the environment, the owner or operator must provide secondary containment that meets the requirements of this section for all new and existing tank systems. 1. Secondary containment systems must be: a. Designe…

1. Secondary containment for tanks must include one or more of the following: a. A liner (external to the tank). b. A double-walled tank. c. An equivalent device (documentation of equivalency must be maintained at the facility). 2. External liner systems must be: a. Designed or o…

An owner or operator must provide ancillary equipment with secondary containment (for example, trench, jacketing, double-walled piping) that meets the requirements of subsections 1 and 2 of section 33.1-24-05-1105, except for: 1. Aboveground piping (exclusive of flanges, joints, …

1. Hazardous wastes or treatment reagents must not be placed in a tank system if they could cause the tank, its ancillary equipment, or the containment system to rupture, leak, corrode, or otherwise fail. 2. The owner or operator must use appropriate controls and practices to pre…

1. The owner or operator shall develop and follow a schedule and procedure for inspecting overfill controls. 2. The owner or operator shall inspect at least once each operating day: a. Aboveground portions of the tank system to detect corrosion or releases of waste. b. Data gathe…

1. Ignitable or reactive wastes may not be placed in tank systems, unless: a. The waste is treated, rendered, or mixed before or immediately after placement in the tank systems so that: (1) The resulting waste, mixture, or dissolved material no longer meets the definition of igni…

A tank system or secondary containment system from which there has been a leak or spill, or if either system is unfit for use, the owner or operator must remove the system from service immediately, and must satisfy the following requirements: 1. Immediately stop the flow of hazar…

At closure of a tank system, the owner or operator must remove or decontaminate all waste residues, contaminated containment system components (liners), contaminated soils, and structures and equipment contaminated with waste, and manage them as hazardous waste, unless subsection…

1. Ignitable or reactive wastes may not be placed in tank systems, unless: a. The waste is treated, rendered, or mixed before or immediately after placement in the tank system so that: (1) Subsection 2 of section 33.1-24-05-967 is complied with; and (2) The resulting waste, mixtu…

1. Incompatible wastes, or incompatible wastes and materials, may not be placed in the same tank system, unless subsection 2 of section 33.1-24-05-967 is complied with. 2. Hazardous waste may not be placed in a tank system that has not been decontaminated and that previously held…

The owner or operator shall manage all hazardous waste placed in a tank in accordance with the requirements of sections 33.1-24-05-400 through 33.1-24-05-474. Under a standardized permit, the following control devices are permissible: thermal vapor incinerator, catalytic vapor in…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

1. Incompatible wastes, or incompatible wastes and materials, may not be placed in the same tank system, unless subsection 2 of section 33.1-24-05-08 is complied with. 2. Hazardous waste may not be placed in a tank system that has not been decontaminated and that previously held …

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…

CHAPTER 33.1-24-05 STANDARDS FOR TREATMENT, STORAGE, AND DISPOSAL FACILITIES AND FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS WASTES AND SPECIFIC TYPES OF HAZARDOUS WASTE MANAGEMENT FACILITIES Section 33.1-24-05-01 Purpose, Scope, and Applicability 33.1-24-05-02 Identification Number…