Oregon Administrative Code

918-100-0080 Work Qualifying for the Master Permit Program (1) A master permit allows construction work in a covered facility if: (a) The work is not "new construction" as defined in these rules and ORS 455.190; (b) The occupancy classification of the building is not changed to a…

918-100-0090 Master Permit Fees (1) The master permit fee for inspection hours shall be the hourly charge of the inspecting jurisdiction. The hourly charge may include the direct costs of providing the service, such as salaries, materials and supplies, as well as indirect expense…

918-100-0100 Master Permit Requirements for Applicants An applicant electing to have a covered facility inspected under a master permit shall: (1) Take out an annual master permit with the inspecting jurisdiction, designate the covered facility involved, define whether the work w…

918-100-0110 Delegation of Special Inspection Programs Each municipality providing industrial and commercial structural, mechanical and plumbing specialty code inspections can request delegation provided it: (1) Files a timely notice under ORS 455.148 or 455.150 covering the basi…

918-100-0120 Clarification of Jurisdiction (1) If an inspecting jurisdiction chooses not to offer the optional minor label program or master permit program, permits and individual inspections shall continue to be required in each program area involved; and (2) The delegation proc…

918-200-0000 General Title OAR 918, division 200 shall be known and may be cited as the “Amusement Ride and Device Specialty Code.” [Publications: Publications referenced are available from the agency.] Statutory/Other Authority: ORS 460.355 Statutes/Other Implemented: ORS 460.35…

918-200-0005 Definitions As used in this code, unless the context requires otherwise: (1) “Administrator” means the administrator of the Building Codes Division. (2) “Alterations/modifications of an amusement ride or device” means any physical change to the structure or mechanism…

918-200-0015 Scope The provisions of this code shall apply to all amusement rides and devices defined in ORS 460.310 and to operators and inspectors of amusement rides. This code does not apply to games or concessions and their associated structures or to pony rides or similar an…

918-200-0020 Uniformity This code shall be applicable and uniform throughout this state and in all municipalities. No municipality shall enact or enforce any ordinance, rule or regulation relating to the same matters encompassed by these rules unless authorized by the Administrat…

918-200-0025 Permits, Inspections and Appeals (1) All amusement rides and amusement devices must be inspected prior to the issuance or renewal of an operating permit. Any defects identified during the inspection that are dangerous to health or safety must be corrected before the …

918-200-0027 Temporary Operation of an Amusement Ride or Device Pending Issuance of an Operating Permit (1) An amusement ride or device may be operated pending the issuance of an operating permit under the following conditions: (a) The ride operator provides, and the division has…

918-200-0030 Division Inspectors (1) The division administrator may appoint and employ qualified inspectors to inspect amusement rides for the division. (2) The division shall maintain a list of inspectors who have notified the division that they are qualified pursuant to OAR 918…

918-200-0040 Authority of Inspector An inspector not employed by the Division may inspect only amusement rides and devices insured or to be insured by the inspector’s employer or principle. Statutory/Other Authority: ORS 460.355 Statutes/Other Implemented: ORS 460.355 History: BC…

918-200-0055 Permit Fee (1) The fee for an annual operating permit for rides and devices shall be $25. (2) The fee for reinspection by the Division shall be $60 per hour, including associated travel time. Statutory/Other Authority: ORS 460.355 Statutes/Other Implemented: ORS 460.…

918-200-0065 Ski Equipment, Federal Exemptions (1) Devices and equipment generally associated with winter sports activities, such as ski lifts, ski tows, J-bars, ski mobiles, chair lifts and aerial tramways, shall be installed and maintained in accordance with ANSI Standard B77.1…

918-200-0070 General Standards and Requirements (1) All codes, standards, and publications adopted by reference in these rules are adopted pursuant to OAR 918-008-0000. (2) Except for devices and equipment subject to OAR 918-200-0065, amusement rides and devices subject to inspec…

918-200-0095 Inspectors, Files and Information (1) Scope. This rule establishes the minimum standards for inspectors, for communication between manufacturers, operators and inspectors, and the required retention of information. (2) To be qualified to inspect amusement rides in Or…

918-200-0100 Bungee Jumping Except for jumps from towers or devices specifically engineered and designed for reverse jumping or catapulting, “bungee catapulting,” “negative jumping,” “reverse jumping,” “launching,” “tandem, double or multiple jumping,” or “sandbagging” shall not …

918-225-0240 Definitions As used in OAR 918, division 225, unless the context requires otherwise: (1) "Agricultural Purposes" means: (a) Sowing, tending, and harvesting of products of the soil grown under natural conditions; (b) Raising of poultry or fowl; (c) Pasturage or raisin…

918-225-0300 Exemptions for Fired Water Heaters Fired water heaters used exclusively for heating water for swimming pools or spas are considered pool boilers and are exempt from the requirements of ORS 480.510 to 480.665 if: (1) Units are equipped with a flow switch or pressure s…

918-225-0310 Exemptions for Refrigerant Piping Systems (1) The requirements of OAR 918-225-0430(2)(e) shall be enforced under this rule for all refrigerant piping systems consisting of welded, brazed or mechanically assembled piping and piping fittings exceeding 2 inches NPS, and…

918-225-0315 Exemptions for Process Piping Systems (1) For the purposes of the Oregon Boiler and Pressure Vessel Specialty Code, the requirements of OAR 918-225-0430(2)(d) shall be applied to only Category "M" fluid service process piping systems, as described in ASME B31.3, Appe…

918-225-0320 Exemptions for Refrigerant or Air Conditioning Pressure Vessels (1) Refrigerant or air conditioning pressure vessels containing three cubic feet, or less, volume of non-corrosive gases are exempt from ORS 480.510 to 480.665 if the pressure vessel is manufactured in a…

918-225-0330 Exemptions for Unfired Pressure Vessels With an Inside Diameter of Six Inches and Less (1) Vessels with an inside diameter or cross section diagonal not exceeding six inches, equipped with an approved pressure relieving device are exempt from ORS 480.510 to 480.665. …

918-225-0340 Exemptions for Pressure Containing Parts of Piping Components The following are exempt from the requirements of ORS 480.510 to 480.665: (1) Pressure containers which are integral parts or components of rotating or reciprocating mechanical devices, including but not l…

918-225-0350 Exemptions for Hot Water Storage Tanks Hot water supply storage tanks heated by steam or any indirect means not exceeding any of the following are exempt from ORS 480.510 to 480.665: (1) A water temperature of 210°F; (2) A nominal water containing capacity of 120 gal…

918-225-0360 Exemptions for Certain Pressure Vessels Pressure vessels for cold water storage, water filter, water softener, or hydro-pneumatic service, and equipped with an ASME-approved pressure/temperature relieving device set at a maximum pressure of 300 psig and a maximum tem…

918-225-0365 Exemptions for Certain Miniature Boilers A miniature boiler used commercially is exempt from the requirements of ORS 480.510 to 480.665, provided the boiler: (1) Does not have more than 1.5 cubic feet of steam space; (2) Is operated at not more than 30 pounds per squ…

918-225-0370 Exemptions for Coil-Type Water Boilers Coil-type water boilers, where the water can flash into steam when released directly to the atmosphere through a manually operated nozzle, are exempt from ORS 480.510 to 480.665 if the following conditions are met: (1) There is …

918-225-0380 Exemptions for Refrigeration Chillers (1) Waterside vessels of refrigeration chillers are exempt under ORS 480.510 to 480.665 if: (a) The design pressure does not exceed 300 pounds per square inch gauge, the temperature does not exceed 210°F., and the system includes…

918-225-0430 Adopted Oregon Boiler and Pressure Vessel Specialty Code (1) The Oregon Boiler and Pressure Vessel Specialty Code is adopted and amended by reference. Any matters included in the referenced publications below that are in conflict with Oregon Revised Statutes or Orego…

918-225-0435 Amendments to the Oregon Boiler and Pressure Vessel Specialty Code The Oregon Boiler and Pressure Vessel Specialty Code is amended pursuant to OAR chapter 918, division 8. Amendments adopted for inclusion into the Oregon Boiler and Pressure Vessel Specialty Code are …

918-225-0445 Other Installation Standards (1) Boilers or pressure vessels not designed or constructed in accordance with the Boiler and Pressure Vessel Code of the American Society of Mechanical Engineers (ASME) may be installed in Oregon if the boiler or pressure vessel was desi…

918-225-0450 Manufacturer’s Data Reports (1) For new boilers or pressure vessels built to ASME or Canadian Standards Association standards, a Manufacturer's Data Report shall be filed with the National Board of Boiler and Pressure Vessel Inspectors before installing any new boile…

918-225-0460 Reporting of Accidents and Conditions of Use (1) Any accident, which includes an explosion, fire or major failure of a vessel or a related appurtenance shall be reported to the chief inspector by telephone or FAX, or both, at the Building Codes Division within 24 hou…

918-225-0465 Boiler Room Usage (1) Every boiler room shall be maintained for exclusive use of boilers and associated systems, equipment and machinery. Storage of non-boiler-related machinery, equipment or materials in a boiler room is prohibited. Flammable liquid or gas container…

918-225-0470 Boiler Operation The owner-user of a boiler, designed for operation at or above 15 psi steam; or 160 psi or 250 F. water shall insure that all boiler control and safety devices are thoroughly inspected and tested at regular intervals consistent with the provisions of…

918-225-0510 Installation of Buried Vessels Under no circumstances shall any pressure vessel subject to the Boiler and Pressure Vessel Laws and these rules be buried underground or located in an inaccessible place. Where necessary to install a vessel underground, it shall be encl…

918-225-0540 Scope of Special Inspector’s Authority (1) General inspection requirements are in ORS 480.560. (2) The type of inspections a special inspector can do is set out in ORS 480.570. (3) The special inspector’s enforcement powers are in ORS 480.660. (4) Appeals from specia…

918-225-0560 Responsibility of Inspectors (1) All deputy and special inspectors shall perform boiler, pressure vessel and pressure piping inspections in accordance with the Oregon Boiler and Pressure Vessel Specialty Code adopted in OAR 918-225-0430 and the following requirements…

918-225-0562 Process Piping Inspector Responsibilities (1) The process piping inspector shall: (a) Inspect the Category "M" fluid service process piping to the extent necessary to be satisfied that it conforms to all applicable examination requirements of ASME B31.3; (b) Verify t…

918-225-0565 Reporting of Immediate Hazards to Health or Safety Deputy and special inspectors shall report immediate hazards to health or safety concerning boilers or pressure vessels to the chief inspector immediately by telephone and also that a notice of defective condition wa…

918-225-0570 Boiler and Pressure Vessel Inspection Schedules Unless the division grants special permission, all inspectors must comply with the following inspection schedule: (1) Power boilers must be inspected, at minimum: (a) Internally — every year, when physical construction …

918-225-0590 Inspection Cycle Extension Program (1) The division shall evaluate written requests from the equipment’s owner or their agent for inspection cycle extensions pursuant to the following criteria: (a) An extension shall be granted for up to twelve (12) months from the e…

918-225-0600 Permits (1) Except as otherwise provided in this rule, an installation permit is required before installing, altering, or repairing a nonexempt boiler or pressure vessel. (2) Notwithstanding section (1) of this rule: (a) An installation permit is not required for min…

918-225-0606 Issuance and Purchase of Minor Repair Permits (1) The Building Codes Division will issue minor repair permits in lots of five at a cost of $175 per lot. Each lot of minor repair permits is valid for one year from the date of purchase. (2) The following persons may pu…

918-225-0609 Use of Minor Repair Permits (1) Only those minor repairs described in OAR 918-225-0612 may be performed under a minor repair permit. (2) A minor repair permit authorizes work on a single boiler or pressure vessel. Multiple minor repairs may be performed under a minor…

918-225-0612 Scope of Work Allowed under Minor Repair Permit (1) Only minor repairs may be performed under a minor repair permit. Minor repairs include, but are not limited to, the non-welded replacement of the following: (a) Low water cut-off; (b) Pressure relief valve; (c) Safe…

918-225-0615 Inspection of Minor Repair Permits (1) The division will randomly inspect at least one permit from each lot of minor repair permits (2) The division will initially select one minor repair permit from each lot for inspection. If the division determines that the work d…

918-225-0618 Misuse of Minor Repair Permits (1) An individual performing work under a minor repair permit misuses the minor repair permit if the work performed does not conform to the Oregon Boiler and Pressure Vessel Specialty Code. (2) The purchaser of a lot of minor repair per…