FAA Eyes Airbus Pump Fixes: Planes Stay Aloft, Bureaucrats Busy

2026-15585, Requirements for Interference-Tolerant Radio Altimeter Systems

In July 2025, President Trump signed the One Big Beautiful Bill Act. Section 40002 of that law re-institutes the Federal Communications Commission's general auction authority and specifically directs the Commission to complete a system of competitive bidding for not less than 100 megahertz in the 3.98-4.2 gigahertz band (Upper C- band). This final rule supports the Federal Communications Commission's July 2026 Report and Order that makes 160 megahertz of the Upper C-band available for terrestrial wireless flexible use via a system of competitive bidding. To ensure safe, efficient, and reliable aviation operations in the presence of wireless signals in the C-band, the Federal Aviation Administration is issuing new regulations that require all radio altimeters to meet specific minimum performance requirements. These new radio altimeters must withstand interference from wireless signals in neighboring spectrum bands and continue to provide accurate altitude readings to both pilots and integrated aircraft safety systems. These regulations require all aircraft equipped with radio altimeters operating under part 121 and those aircraft with radio altimeters operating under part 129 with 30 or more passenger seats or a payload capacity of more than 7,500 pounds to comply with the minimum performance requirements by December 30, 2030, which is prior to the date the Federal Communications Commission authorizes the use of the Upper C-band for new wireless services, as stated in its Report and Order. All other aircraft equipped with radio altimeters that are required to comply with part 91, including aircraft operating under parts 125, 133, 135, 136, 137, 194, and all other aircraft operating under part 129 that are not subject to the initial deadline, must comply with the same minimum performance requirements on or before October 31, 2034.

2026-13440, Enabling Supersonic Overland Flight

The FAA wants to let supersonic planes fly over land again by updating old rules that banned them because of loud sonic booms. Thanks to new tech that keeps booms quiet, this change will open the door for faster, cooler flights across the U.S., helping America lead the world in supersonic travel. People and companies interested in supersonic flight should share their thoughts by August 17, 2026.

2026-13126, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility; Extension of Comment Period

The FAA is giving more time—until August 5, 2026—for people to share their thoughts on new rules that would limit drone flights near important fixed sites like power plants or airports. This affects drone operators and facility owners who want to keep the skies safe and secure. No new costs yet, just extra time to weigh in and help shape the rules.

2026-08943, Designation-Restrict the Operation of Unmanned Aircraft in Close Proximity to a Fixed Site Facility

The FAA is proposing new rules to keep drones away from certain important fixed sites like power plants or airports to keep everyone safe and secure. If you own or operate one of these sites, you can request a drone flight restriction zone to protect your property and people nearby. Comments are open until July 6, 2026, and these changes could affect drone pilots and site operators, but no big costs are expected.

2026-18372, Airworthiness Directives; Airbus SAS Airplanes

The FAA proposes to supersede Airworthiness Directive (AD) 2023-07-02, which applies to all Airbus SAS Model A330-200, -300, -800, and -900 series airplanes; and Model A340-200, -300, -500, and -600 series airplanes. AD 2023-07-02 requires replacing the doghouse door lock placard with an improved instruction placard. Since the FAA issued AD 2023-07-02, it was determined that additional parts need to be modified. This proposed AD would continue to require the actions in AD 2023-07-02 and would expand the list of affected parts. This proposed AD would also prohibit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.

2026-18376, Airworthiness Directives; Bombardier, Inc. Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-2A12 airplanes. This proposed AD was prompted by reports of fuel leakage near rib 6 during production pressure testing. An investigation found oversized holes in a certain outboard shear-tie. This proposed AD would require an inspection of the fasteners and fastener holes at rib 6 for discrepancies and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.

Previous: 2026-18372, Airworthiness Directives; Airbus SAS Airplanes

The FAA proposes to supersede Airworthiness Directive (AD) 2023-07-02, which applies to all Airbus SAS Model A330-200, -300, -800, and -900 series airplanes; and Model A340-200, -300, -500, and -600 series airplanes. AD 2023-07-02 requires replacing the doghouse door lock placard with an improved instruction placard. Since the FAA issued AD 2023-07-02, it was determined that additional parts need to be modified. This proposed AD would continue to require the actions in AD 2023-07-02 and would expand the list of affected parts. This proposed AD would also prohibit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.

Next: 2026-18376, Airworthiness Directives; Bombardier, Inc. Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-2A12 airplanes. This proposed AD was prompted by reports of fuel leakage near rib 6 during production pressure testing. An investigation found oversized holes in a certain outboard shear-tie. This proposed AD would require an inspection of the fasteners and fastener holes at rib 6 for discrepancies and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.