Michigan Administrative Code

R 400.12510 Independent living agreement. Rule 510. (1) There must be a mutual agreement between the youth and the agency specifying all the following: (a) The responsibilities of the agency and the youth. (b) A plan for education or work. (c) An agreement for the youth to meet w…

R 408.12510 Availability of MIOSHA referenced standards. Rule 2510. The following Michigan Occupational Safety and Health Administrative (MIOSHA) standards are referenced in these rules. Up to 5 copies of these standards may be obtained at no charge from the Michigan Department o…

R 400.12511 Termination. Rule 511. (1) When an agency terminates its independent living services for a youth, the agency shall document all the following information in the case record within 30 calendar days of termination of its services: (a) The reason for the termination. (b)…

R 400.12601 Department authorization. Rule 601. The department shall authorize an agency to evaluate applicants for adoption. History: 1998-2000 AACS; 2023 AACS.

R 325.12601 Applicability. Rule 2601. The provisions of this part apply to all persons providing bottled drinking water for drinking or household purposes. History: 1979 AC.

R 408.12601 Scope. Rule 2601. This part sets forth rules, not covered in other standards, for the safety of employees in all places of employment where a hazard may exist in the use of metalworking machinery. Press brakes and handheld portable powered tools are not included in th…

R 408.12602 Applicability. Rule 2602. (1) A metalworking machine with the point of operation inaccessible or remote from the operator and other assigned employees shall not be required to have guarding for the point of operation. (2) The general rules of this part shall apply to …

R 400.12602 Program statement. Rule 602. (1) An agency shall have and follow a current written program statement. (2) The statement must include all the following information: (a) Services and functions provided directly or indirectly. (b) Geographical area covered. (c) Eligibili…

R 325.12602 Application for approval of source. Rule 2602. (1) A person providing bottled drinking water shall submit an application to the department requesting approval of the source of water being used or planned to be used for bottled water. A person may request approval of m…

R 325.12603 Sources of water; monitoring. Rule 2603. If water is obtained from a source other than a type I or type II public water supply, the department may require a person providing bottled water to sample the source of water from time to time and submit records of that sampl…

R 408.12603 Definitions; A to C. Rule 2603. (1) "Aisle" means a designated path of travel for vehicles and employees. (2) "Alligator shear" means a machine having a powered blade and a fixed blade which creates a shearing action when the moving blade meets the fixed blade. (3) "A…

R 400.12603 Policy and procedures. Rule 603. (1) An agency shall have and follow written policies and procedures for the adoption services provided. (2) The policies and procedures must cover at least all the following areas: (a) Orientation. (b) Training requirements. (c) Adopti…

R 400.12604 Orientation. Rule 604. (1) An agency shall provide an orientation for prospective applicants for adoption before an adoptive application is provided. (2) The orientation must include a review of all the following: (a) Program statement, policies, and procedures. (b) N…

R 408.12604 Definitions; F to L. Rule 2604. (1) "Fixed barrier" means a type of guard, attached by fasteners that cannot be readily removed, that keeps the operator from the point of operation. (2) "Interlocked barrier" means a type of guard with a control interlocked with a mach…

R 408.12605 Definitions; M, O. Rule 2605. (1) "Metal band saw" means a machine that is equipped with 2 wheels on which a continuous blade is used for metal cutting purposes. (2) "Metal embossing machine" means a machine that imparts a design to a piece of metal by pressure. (3) "…

R 400.12605 Adoptive family evaluation. Rule 605. (1) An agency social service worker shall complete a written adoptive evaluation within 90 days of the family signing an adoption application and prior to approving a family for adoption. (2) The report must include the dates and …

R 325.12605 Maintenance of records. Rule 2605. A person providing bottled drinking water shall maintain records of all sources from which water is purchased or obtained for bottled water and shall submit those records to the department on an annual basis. Page 310 Courtesy of Mic…

R 325.12606 Rescission or suspension of approval. Rule 2606. Upon its finding that a person has submitted false information on an application submitted to the department for approval of a source for bottled water pursuant to R 325.12602, or if a source for bottled water does not …

R 400.12606 Training requirements. Rule 606. An agency shall document that an applicant for adoption has, at a minimum, training in all the following areas: (a) Separation. (b) Attachment and bonding. (c) Child development, including safe sleep practices for children under 1 year…

R 408.12606 Definitions; P. Rule 2606. (1) "Pay off," sometimes called a top hat, means an uncoiling device upon which the undrawn coil of wire rests. (2) "Pinch point" means a point where it is possible to be caught between the moving parts of a machine and the material in proce…

R 408.12607 Definitions; R, S. Rule 2607. (1) "Remote" means that an operator or other assigned employee who is operating or attending a machine cannot, because of distance or location, place any part of his or her body within the point of operation when a hazard exists. (2) "Riv…

R 400.12607 Agency recommendation. Rule 607. (1) An agency shall recommend the appropriate action consistent with the facts contained in the adoptive evaluation. An agency shall make a written recommendation based on the findings of the adoptive family evaluation. (2) The recomme…

R 400.12608 Adoptive family evaluation record. Rule 608. (1) An agency shall retain a case record for each applicant for adoption. Page 41 Courtesy of Michigan Administrative Rules (2) The record must contain all the following: (a) Orientation documentation as required by R 400.1…

R 408.12608 Definitions; T to W. Rule 2608. (1) "Tumbling mill" means a machine with a powered revolving container which is used to dry, smooth or polish metal parts. (2) "Wire drawing machine" means a machine that draws or pulls metal wire or rod through a predetermined size of …

R 408.12611 Employer responsibility. Rule 2611. An employer shall: (a) Provide training to each employee as to the potential hazards and safe operation of the assigned job. (b) Maintain metalworking machinery, in conformance with this part. (c) Establish and maintain a lockout pr…

R 408.12612 Employee responsibility. Rule 2612. An employee shall: (a) Not use machinery and equipment unless authorized and trained in its use. (b) Report defective machinery and equipment and hazardous conditions, when detected, to his supervisor. (c) Not remove guards from mac…

R 408.12615 Aisles, floors, and platforms. Rule 2615. (1) The outline of a designated aisle shall be marked or otherwise indicated. (2) A designated aisle shall be not less than 4 feet wide and access shall be maintained from a work station to an aisle. History: 1979 AC; 1997 AAC…

R 408.12616 Machine and equipment installation. Rule 2616. (1) A metalworking machine or equipment must be installed so that the normal operator's position is not in an aisle, or the employee shall be protected by a guardrail system in compliance with General Industry Safety and …

R 408.12617 Controls. Rule 2617. (1) When a presence-sensing device is used as a safety device, the control shall incorporate a fail-safe feature. (2) Machine start controls shall be designed and installed or guarded to prevent unintentional activation by contact with objects or …

R 408.12618 Maintenance and lubrication. Rule 2618. (1) A power source of any metalworking machine or equipment to be repaired or serviced shall be locked out and, where required, residual pressure relieved by each employee doing such work if unexpected motion would cause injury,…

R 408.12620 Chip guards; protection from coolant splash. Rule 2620. (1) Chips which create a hazard shall be controlled by a chip guard that is located between the point of operation and any employee within range. (2) If a machine uses a coolant, an employee shall be protected fr…

R 408.12622 Electric magnets and vacuum chucks. Rule 2622. (1) A grinding machine with a rotating table and equipped with a magnetic or vacuum chuck to hold the stock shall be interlocked to prevent contact between the stock and tool, unless the stock is secured to the table or c…

R 408.12632 Circular metal saws. Rule 2632. (1) A circular metal saw shall meet all of the following: (a) Have a guard made of material not less than 1/8 inch thick and capable of protecting the operator from broken teeth of the blade and chips. The guard shall enclose not less t…

R 408.12633 Bar stock and rod machines; screw machines; tread machines. Rule 2633. A bar stock and rod machine, screw machine or thread machine must have the bar stock that extends beyond the machine guarded by a trough or tube or guarded by a guardrail system in compliance with …

R 408.12634 Planers. Rule 2634. (1) A planer shall have the openings in the bed under the table covered, and have a barrier protecting an employee if the table or material travels within 18 inches of a fixed object, such as a wall or post. (2) An employee shall not ride the table…

R 408.12635 Metal band saws. Rule 2635. (1) A vertical metal band saw shall be guarded as follows: Page 9 Courtesy of Michigan Administrative Rules (a) The band wheels and all portions of the blade, except as provided by subdivision (b) of this subrule, shall be fully enclosed by…

R 408.12636 Metal embossing machines. Rule 2636. (1) A press-type metal embossing machine shall be guarded at the point of operation as prescribed in the general industry safety standards commission standards, Part 23. Hydraulic Power Presses or Part 24. Mechanical Power Presses,…

R 408.12637 Powered feed rolls. Rule 2637. Powered feed rolls shall have 1 of the following: (a) The in-running side of the feed rolls guarded by a barrier, fixed or adjustable, so designed that the material can be fed without permitting the fingers to be caught between the feed …

R 408.12638 Wire drawing machines. Rule 2638. (1) An employer shall ensure that a wire drawing machine has 1 of the following: (a) An emergency stop device adjacent to the block available to shut down the machine. Page 10 Courtesy of Michigan Administrative Rules (b) An emergency…

R 408.12639 Boring, honing, reaming, and drilling. Rule 2639. (1) An employer shall ensure that when boring, honing, reaming, or drilling, all of the following provisions apply: (a) Except for hand-held honing, the workpiece is secured by a device to prevent it from being turned …

R 408.12640 Milling. Rule 2640. When milling, all of the following provisions apply: (a) Manual adjustments or measurements at the point of operation shall be made only after the tool and workpiece have stopped. (b) Machine torque shall not be used to loosen nuts. (c) A chip guar…

R 408.12641 Roll-form machines. Rule 2641. (1) An automatically fed roll-form machine shall have a shield which runs the entire length of the point of operation and which will prevent horizontal access to the rolls or a continuous stop cable shall be provided along the length of …

R 408.12642 Powered benders. Rule 2642. (1) An employer shall ensure that a powered bender has 1 of the following: (a) A barrier or enclosure guard that is designed to protect the operator from the pinch points when clamping parts in the bender. (b) A single-stroke hand control d…

R 408.12643 Tumbling mills, barrels and revolving cylinders. Rule 2643. (1) A tumbling mill, barrel or revolving cylinder shall have an enclosure to a height of 42 inches to protect an employee if there are any moving projections. Page 12 Courtesy of Michigan Administrative Rules…

R 408.12644 Alligator shears. Rule 2644. An alligator shear shall have the jaws enclosed with a guard which adjusts to the size and shape of the material. History: 1979 AC.

R 408.12645 Riveters, braders and stakers. Rule 2645. (1) A vertical or horizontal ram on a riveter, brader or staker shall be guarded by a barrier, device or enclosure to protect the operator from the point of operation or an awareness device shall be used to warn the operator h…

R 408.12646 Powered clamping device. Rule 2646. An operator of a powered clamping device that is used for holding a workpiece shall be protected by employing 1 of the following methods: (a) Guarding or adjusting so that the opening between the clamp and workpiece insertion is not…