Chapter 3745-51 | Identification and Listing of Hazardous Waste

(A) Except during pressure releases, each pressure relief device in gas or vapor service shall be operated with no detectable emissions, as indicated by an instrument reading of less than five hundred parts per million (ppm) above background, as measured by the method specified i…

(A) Each sampling connection system shall be equipped with a closed-purge, closed-loop, or closed-vent system. This system shall collect the sample purge for return to the process or for routing to the appropriate treatment system. Gases displaced during filling of the sample con…

(A) (1) Each open-ended valve or line shall be equipped with a cap, blind flange, plug, or a second valve.(2) The cap, blind flange, plug, or second valve shall seal the open end at all times except during operations requiring hazardous secondary material stream flow through the …

(A) Each valve in gas or vapor or light liquid service shall be monitored monthly to detect leaks by the methods specified in paragraph (B) of rule 3745-51-763 of the Administrative Code and shall comply with paragraphs (B) to (E) of this rule, except as provided in paragraphs (F…

(A) Pumps and valves in heavy liquid service, pressure relief devices in light liquid or heavy liquid service, and flanges and other connectors shall be monitored within five days by the method specified in paragraph (B) of rule 3745-51-763 of the Administrative Code if evidence …

(A) Delay of repair of equipment for which leaks have been detected will be allowed if the repair is technically infeasible without a hazardous secondary material management unit shutdown. In such a case, repair of this equipment shall occur before the end of the next hazardous s…

(A) The remanufacturer or other person who stores or treats the hazardous secondary material in a hazardous secondary material management units using closed-vent systems and control devices subject to rules 3745-51-750 to 3745-51-764 of the Administrative Code shall comply with r…

(A) A remanufacturer or other person who stores or treats the hazardous secondary material subject to the requirements of rule 3745-51-757 of the Administrative Code may elect to have all valves within a hazardous secondary material management unit comply with an alternative stan…

(A) A remanufacturer or other person who stores or treats the hazardous secondary material subject to the requirements of rule 3745-51-757 of the Administrative Code may elect for all valves within a hazardous secondary material management unit to comply with one of the alternati…

(A) Each remanufacturer or other person who stores or treats the hazardous secondary material subject to rules 3745-51-750 to 3745-51-764 of the Administrative Code shall comply with the test methods and procedures requirements provided in this rule.(B) Leak detection monitoring,…

(A) (1) Each remanufacturer or other person who stores or treats the hazardous secondary material subject to rules 3745-51-750 to 3745-51-764 of the Administrative Code shall comply with the recordkeeping requirements of this rule.(2) A remanufacturer or other person who stores o…

(A) Rules 3745-51-780 to 3745-51-789 of the Administrative Code apply to tanks and containers that contain hazardous secondary materials excluded under the remanufacturing exclusion in paragraph (A)(27) of rule 3745-51-04 of the Administrative Code, unless the tanks and container…

As used in rules 3745-51-780 to 3745-51-789 of the Administrative Code, all terms not defined herein have the meaning given in the Resource Conservation and Recovery Act and Chapters 3745-50 to 3745-57, 3745-65 to 3745-69, 3745-205, 3745-256, and 3745-266 of the Administrative Co…

(A) This rule applies to the management of hazardous secondary material in tanks and containers subject to rules 3745-51-780 to 3745-51-789 of the Administrative Code.(B) The remanufacturer or other person who stores or treats the hazardous secondary material shall control air po…

(A) Material determination procedure to determine average volatile organic (VO) concentration of a hazardous secondary material at the point of material origination.(1) Determining average VO concentration at the point of material origination. A remanufacturer or other person who…

(A) This rule applies to the control of air pollutant emissions from tanks for which paragraph (B) of rule 3745-51-782 of the Administrative Code references the use of this rule for such air emission control.(B) The remanufacturer or other person who stores or treats the hazardou…

(A) Applicability. This rule applies to the control of air pollutant emissions from containers for which paragraph (B) of rule 3745-51-782 of the Administrative Code references the use of this rule for such air emission control.(B) General requirements.(1) The remanufacturer or o…

(A) This rule applies to each closed-vent system and control device installed and operated by the remanufacturer or other person who stores or treats the hazardous secondary material to control air emissions in accordance with standards of rules 3745-51-780 to 3745-51-789 of the …

(A) The remanufacturer or other person who stores or treats the hazardous secondary material shall inspect and monitor air emission control equipment used to comply with rules 3745-51-780 to 3745-51-789 of the Administrative Code in accordance with the applicable requirements spe…

(A) Each remanufacturer or other person who stores or treats the hazardous secondary material subject to requirements of rules 3745-51-780 to 3745-51-789 of the Administrative Code shall record and maintain the information specified in paragraphs (B) to (J) of this rule, as appli…